American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Super-Smooth Poly Finish Gadsden AL

Synthetic steel wool creates an even, silky smooth finish that’s a joy to look at and feel. This age-old two-step technique is commonly used on shellac and lacquer finishes, but it can work well on water- and oil-based polyurethane, too. The only drawback with poly is that it is difficult to bring up to a high gloss.

Gadsden Mall
(256) 543-4900
1001 Rainbow Dr
Gadsden, AL
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Kmart 4475 / Cross Merch
(256) 547-5703
201 George Wallace Dr
Gadsden, AL
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Fastenal-Attalla
256-570-0238
84 Industrial Blvd Attalla, AL, 35954
Attalla, AL
 
Warren Ace Hardware
(256) 435-6383
1420 Pelham Rd S, Joy Christian Book Store
Jacksonville, AL
 
Strickland's Hardware
(256) 447-9771
112 N Center Ave
Piedmont, AL

Data Provided by:
LOWE'S OF GADSDEN, ALA.
256 543-1543
615 GEORGE WALLACE DRIVE GADSDEN, AL, 35903
Gadsden, AL
 
Lowe's
(256) 543-1543
615 George Wallace Drive
Gadsden, AL
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Weathers Hardware & Appliance
(256) 593-4218
202 W Mill Ave, Hwy. 205 and Hwy. 168 Crossing
Boaz, AL
 
Kmart 4835 / Cross Merch
(256) 927-8000
1525 Chestnut Byp
Centre, AL
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Whitley Hardware
(205) 466-3033
86343 US Hwy 278
Altoona, AL

Data Provided by:
Data Provided by:

Super-Smooth Poly Finish

Super-Smooth Poly Finish

A Defect-Free, Even Finish with a Brush

by Eric Smith

Polyurethane is a tough, high-quality finish, ideal for tabletops and other surfaces that take a lot of abuse. But no matter how clean your finishing area or how good your brushing technique, a few bubbles, dust particles and streaky spots always manage to sneak into the final coat (Photo 1). Directions on the can don’t say anything about it—leaving you to assume a less-than-perfect finish must be your own fault. However, the solution is quite simple—rub out the finish with fine sandpaper and synthetic steel wool. Sanding removes defects and levels ridges.

Photo 1: The Problem: A few dust nibs, broken brush bristles and bubbles are almost inevitable on big horizontal surfaces finished with slow-drying polyurethane. 

Synthetic steel wool creates an even, silky smooth finish that’s a joy to look at and feel. This age-old two-step technique is commonly used on shellac and lacquer finishes, but it can work well on water- and oil-based polyurethane, too. The only drawback with poly is that it is difficult to bring up to a high gloss. If a satin or semi-gloss look is what you’re after, this technique will give you great results.

Materials and Supplies

Sandpaper

Sandpaper is used to flatten the finish and remove dust nibs and brush marks. Stearated aluminum-oxide sandpaper is by far the best product for sanding a finish. Stearated paper has dry lubricants that help prevent “corning” or the balling up of finish on the paper. Wet-dry silicon-carbide paper balls up like crazy if you don’t use water as a lubricant. The trouble with wet sanding is the water slurry can make it difficult to see your progress.  

Synthetic Steel Wool

I used synthetic steel wool on both water- and oil-based polyurethane. Traditional steel wool is not recommended for water-based finishes; it sheds steel particles that leave a mess and give the user steel wool slivers. Synthetic steel wool pads equivalent to 00 steel wool are widely available at home centers and hardware stores. Fine synthetic wool equivalent to 0000 steel wool is harder to find. I had good luck at auto-body supply stores and mail-order woodworking suppliers (see Sources, below). 

Powdered Abrasives

Pumice and rottenstone are sold at some paint stores and at woodworking suppliers. Pumice is ground volcanic glass that comes in grades from  1F (coarse) to 4F (fine). Rottenstone is even finer than 4F pumice. It’s made of ground limestone (see Sources, below).

Build a Good Foundation for the Finish

1. I use 220-grit sandpaper for final sanding on raw wood. I always sand a little bit longer than I think is necessary. Then I vacuum thoroughly and wipe the wood with a clean, soft cloth until I stop getting dust on my fingers when I run them over the wood. 
2. Use grain filler on open-pored woods, such as oak or walnut....

Click here to read the rest of the article from American Woodworker