American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Super-Tune Your Tools with a Dial Indicator Fort Morgan CO

A dial indicator is nothing more than a spring-loaded rod, a needle and a dial. Move the rod up or down and the needle rotates around the dial's face. The dial tells you how many thousandths of an inch the rod has traveled. The one at right is measuring the thickness of a dollar bill at .003 in.

Mr. D'S Ace Home Center
(970) 867-3303
1000 East Platte Avenue
Fort Morgan, CO
 
Ft Morgan - Auth Hometown
(970) 867-5200
1997 E Piatte Ave
Fort Morgan, CO
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12.5-17.5
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12.5-17.5

Bloedorn Lumber Building Mtrls
(970) 867-5646
130 State Street
Fort Morgan, CO
 
Country Do it Best Hardware
(970) 483-7312
218 Main St.
Wiggins, CO
 
The Home Depot
(303)526-4347
1014 El Rancho Road
Golden, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Fastenal- Ft. Morgan
970-867-4475
19873 US Highway 34 Ft. Morgan, CO, 80701
Ft. Morgan, CO
 
Murdoch's Ranch & Home Supply
(970) 542-1515
1207 W. Platte Avenue
Fort Morgan, CO
 
Farm & Home Hardware
(970) 842-2879
122 Custer St
Brush, CO
 
Frank Paxton Lumber Company - Woodcrafter's Store
(303) 399-6047
4837 Jackson Street PO Box 16343
Denver, CO

Data Provided by:
The Home Depot
(719)266-5165
5660 E Woodmen Road
Colorado Springs, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Data Provided by:

Super-Tune Your Tools with a Dial Indicator

Super-Tune Your Tools with a Dial Indicator



Machinists use a simple measuring device called a dial indicator for setting up metalworking equipment. It works great in the woodshop, too, though for woodworking, you don't need a real fancy model. I found  a perfectly adequate dial indicator, complete with all the accessories, for only $18 (see below). The big advantage of using a dial indicator for setting up your machines is that you get instant, clear readings. The needle shows you exactly how far you've gone when you make a minute adjustment. Let's be honest, though. Fine-tuning a machine is fussy business. Even with a dial indicator, it takes some patience and finesse. Grab a comfortable stool, and let's begin with the tablesaw.



What is a Dial Indicator?
A dial indicator is nothing more than a spring-loaded rod, a needle and a dial. Move the rod up or down and the needle rotates around the dial's face. The dial tells you how many thousandths of an inch the rod has traveled. The one at right is measuring the thickness of a dollar bill at .003 in. A complete dial indicator kit also contains a magnetic base, a long articulating arm and a set of contact points. The heavy magnetic base holds the instrument absolutely rigid on any metal surface. It's not electronic (there's no cord to plug in); you flick a switch to raise or lower the magnet inside the base.
The articulating arm is used for holding the dial at a distance from the base. It's tricky to adjust, so we won't use it for these two jobs. Contact points screw onto the bottom of the measuring rod. Each one has a special shape for measuring different kinds of objects. We'll be using three contact points: a ball, a disc and a bent arm.

Zero the Dial
The first step in using a dial indicator is to turn the dial so the zero mark lines up with the needle. This way, you don't have to add or subtract any numbers to calculate how far the needle moves when measuring a distance. Let's practice on the top of the tablesaw. Install a disc contact point on the end of the rod and place the base on the saw. Turn on the magnet. Clamp the dial and rod so the contact point touches the table and slightly compresses the spring-loaded rod. Turn the dial to zero and you're ready to go.

Tablesaw Tune-Up
Here we're going to make sure the blade, fence and miter-gauge slot are absolutely parallel to each other. This reduces the chances of kickback, eliminates burning and produces the smoothest cut. Install the ball contact point on the measuring rod. If your miter gauge wiggles in the slot, you'll have to take out the play for an accurate reading with the dial indicator. Simply push the miter gauge and bar toward one side while you measure. Always push to the same side.

Align the Blade to the Miter-Gauge Slot

PHOTO 1:
Measure the front of the blade. Raise the blade as high as it will go. Turn off the magnet. Clamp the b...

Click here to read the rest of the article from American Woodworker