American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Swingin' Storage Liberal KS

To install a panel, insert the longer dowel in the top tool holder until the bottom;dowel;slips into the bottom tool holder. The long top dowel; must extend through both rings of the tool holder to keep the panel from falling out.

Liberal -Auth Hometown
(620) 624-6200
1010 S Kansas Ave Ste 7
Liberal, KS
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:13-18
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:13-18

Mead Lumber
(620) 624-3885
2000 N Kansas Ave
Liberal, KS
 
The Home Depot
(913)631-1005
15501 W 67th St
Shawnee, KS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(620)275-5943
3110 E Kansas Ave
Garden City, KS
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(316)773-1988
8444 W McCormick Ave
Wichita, KS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Westlake Ace Hardware
(620) 624-1599
1601 N Kansas Ave
Liberal, KS
 
Fastenal- Liberal
620-626-6007
832 E. Pancake Blvd Liberal, KS, 67901
Liberal, KS
 
The Home Depot
(913)789-8899
5700 Antioch
Merriam, KS
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(913)727-1978
5000 S 4th Street
Leavenworth, KS
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(620)728-0460
1907 E 17th Avenue
Hutchinson, KS
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Swingin' Storage

Swingin' Storage



I like to store hardware in its original package on a Peg-Board wall in my shop. I've devised some swinging panels for the wall that give me a lot more usable space. To make the panels, you'll need 1/8" Peg-Board, a 3/4" dia. dowel rod, and Peg-Board tool holders.

Make the panels by cutting 12" x 12" pieces from the Peg-Board. For each panel, cut one dowel 2-1/2" long and one 5" long. Cut a 1/8" wide groove in one end of both dowels and slide the dowels onto the panels. Fasten the dowels with screws. 


To install a panel, insert the longer dowel in the top tool holder until the bottom dowel slips into the bottom tool holder. The long top dowel must extend through both rings of the tool holder to keep the panel from falling out. Each pair of tool holders holds up to six panels. 

I also cut a 1/8" wide slot in a 12" length of 2x4 to use as a base for the panels so I can remove a panel from the tool rack and set it on my workbench.

--Mark Thiel



Click here to read the rest of the article from American Woodworker