American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

T-Track Apex NC

Some T-tracks require special connectors that are only available from one supplier. Pre-drilled for Easy Mounting We prefer T-tracks that are pre-drilled and countersunk to accept No. 6 or bigger wood screws (Photo 3). It's also nice to have screw holes spaced no more than 5 in. apart.

The Home Depot
(919)387-6554
1000 Vision Dr
Apex, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)851-5554
2031 Walnut Street
Cary, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)661-1393
2540 Timber Dr
Garner, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)844-7418
9517 Strickland Rd
Raleigh, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Klingspor’s Woodworking Shop of Raleigh
(919) 876-0707
3141 Capital Blvd.Capital Square
Raleigh, NC

Data Provided by:
Robbins Custom Sawing and Lumber for Natural Edge Slabs
(919) 779-0719
2200 Bull Run Drive
Apex, NC

Data Provided by:
The Home Depot
(919)552-2881
901 E Broad Street
Fuquay Varina, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Raleigh/Durham, NC
(919) 781-1911
4317 Pleasant Valley Road
Raleigh, NC

Data Provided by:
The Home Depot
(919)419-0208
3701 MT Moriah Road
Durham, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)217-3093
1020 Shopps At Midway
Knightdale, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

T-Track

T-Track


T-track is a versatile product that has many great uses around the shop. It can be attached to the fence of a chop saw, drill press or router table to provide a quick, secure place to attach feather boards, stops and hold-downs. It also makes a great addition to jigs and fixtures with parts that need to be adjustable or easily removed. At first glance, all T-tracks look pretty much the same. There are, however, several subtle but important differences among brands. We bought eleven brands commonly available and put them to the test to see which ones we liked best.

Sizes and Prices
T-track is available in lengths from 1 ft. to 12 ft. and averages about $4.50 per lineal foot. It is usually sold in 1- or 2-ft. increments, but some brands can be special ordered to a specific length. Most T-tracks are approximately 3/4 in. wide with a thickness of either 3/8  or 1/2 in. (see Chart). All but one are made of extruded aluminum.

PHOTO 1:
We like T-track that accepts the hex head of a standard bolt. It will save you from having to buy the special connectors that some tracks require.

 

PHOTO 2:
Some T-tracks have a deep slot. It's deep enough to accept a hex nut and is a feature that will increase your connecting and fastening options.

Features We like
Accepts Standard Hardware T-tracks that accept standard hex head bolts and nuts as connectors are a big plus (Photos 1 and 2), because standard nuts and bolts are readily available at hardware stores. This means you won't get stuck in the middle of a project because you don't have the right connector. Some T-tracks require special connectors that are only available from one supplier. Pre-drilled for Easy Mounting We prefer T-tracks that are pre-drilled and countersunk to accept No. 6 or bigger wood screws (Photo 3). It's also nice to have screw holes spaced no more than 5 in. apart. Closely spaced holes mean more holes for more mounting screws and less risk of pulling the T-track off the mounting surface. Also, if you need to cut the T-track shorter, you will still have a hole near the end. If you need to add screw holes to a T-track, you can drill them yourself. It's a bit of a hassle but not difficult (Photos 4 and 5). Some T-tracks even come with a groove to help you center the drill bit. A groove on the bottom is best because drilling the shank hole from the top leaves a burr on the bottom that must be removed with a file.

PHOTO 3:
T-tracks pre-drilled to accept No. 6 or larger screws have better holding strength than the tracks that are drilled for No. 4 screws.


PHOTO 4:
Drill the shank hole from the bottom of the T-track with a 5/32-in.-dia. bit. Some T-tracks have a groove to help center the bit; it's helpful but not essential. A pencil line and center punch also work well.

Grooved for Glue

Click here to read the rest of the article from American Woodworker