American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tablesaw Box Joints Springville UT

Box joints have alternating pins and sockets. To fit together, one piece has pins where the mating piece has sockets (Fig. B, page, 70). The challenge is to cut pins and sockets that are virtually the same size, with paper-thin tolerances for fitting the joint.

The Home Depot
(801)418-1014
1550 S University Ave
Provo, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(801)763-8640
885 W Grassland Drive
American Fork, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Spanish Fork - D
(801) 798-9856
900 E Expwy Ln
Spanish Fork, UT
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Parley's Do it Best Hardware
(801) 822-5200
260 South 1200 West
Orem, UT
 
White Cap- Orem
801-765-1440
555 South 1325 W Orem, UT, 84058
Orem, UT
 
The Home Depot
(801)226-2353
535 S Lindon Park Dr
Lindon, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Kmart 3765 / Cross Merch
(801) 377-2084
1165 S University Ave
Provo, UT
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Towne Centre Mall
(801) 852-2500
1200 Towne Centre Blvd Spc C
Provo, UT
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

LOWE'S OF OREM, UT.
801 229-1485
140 WEST UNIVERSITY PARKWAY OREM, UT, 84058
Orem, UT
 
Lowe's
(801) 229-1485
140 West University Parkway
Orem, UT
Hours
M-SA 6 am - 10 pm
SU 8 am - 9 pm

Tablesaw Box Joints

Tablesaw Box Joints

A shop-made jig with micro-adjust guarantees perfect joints.

by Tim Johnson

Box joints are the savvy woodworker’s alternative to dovetails. Strong, great-looking and quickly made, box joints are an especially good choice when you have a large number of items to produce. To make them, you need your tablesaw, a miter gauge, a dado set and a simple shop-made jig (Fig. A, below). I’ll show you how to build the jig and use its micro-adjust system to dial in perfect-fitting box joints. 

Box joints have alternating pins and sockets. To fit together, one piece has pins where the mating piece has sockets (Fig. B, page, 70). The challenge is to cut pins and sockets that are virtually the same size, with paper-thin tolerances for fitting the joint. Fortunately, the jig can make paper-thin adjustments. It also automatically positions both pieces so their pins and sockets are correctly offset.

Design Details

Pins and sockets can be wide or narrow to suit your project. To size them appropriately, you merely adjust the width of the dado set. For example, to cut 1/4-in.-wide pins and sockets, use a 1/4-in.-wide dado set. The blade’s height determines the length of the pins and sockets. This length matches the thickness of your box pieces. Flat-bottomed dadoes are a must for good-looking joints. 

It’s best to start with your box pieces oversize and trim them to final width after you cut and fit the joints. Box joints usually turn out to be wider than the sum of the pin and socket widths because of the fit-tolerance between each pin and socket. Starting oversize allows you to compensate. 

Photo 1: Set the blade height using a piece from your project. Place the piece on the jig’s carriage and raise the blade. 

A scrap piece held on top tells you when the blade is exactly even with the workpiece. Before moving on to the next step, make sure the miter gauge bar slides smoothly without any side-to-side play. 

Photo 2: Clamp the adjustable fence temporarily to the carriage and cut a slot through both pieces. After cutting, thickness-plane a 12-in.-long piece to exactly fit the slots’ width. Cut this piece into three keys. Trim one key to two-thirds the size of the slot’s height. 

Photo 3: Use three hardwood keys to position the adjustable fence on the carriage. Glue one key in the fence slot. Fit the second key in the carriage slot and sandwich the spacer key in between. Securely clamp the fence to the carriage while butting the three keys snugly together. Drill pilot holes and fasten the fence. Remove the clamps and the two temporary keys. 

Photo 4: Micro-adjust blocks allow you to fine-tune the jig by paper-thin amounts. Attach one block to the carriage base. Butt the second block against the first, with two pieces of paper between them. Fasten this block to the adjustable fence. The space between the carriage bloc...

Click here to read the rest of the article from American Woodworker