American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tablesaw Extension Clarksburg WV

There’s not enough room in my garage shop for a tablesaw with a 52-in.-capacity rip fence. But no worries—I don’t need one! To make wide cuts, I simply install a shop-made extension that bridges my saw to the wall—and doubles its 30-in. rip capacity!

The Home Depot
(304)848-0610
1180 West Main Street
Bridgeport, WV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Marsh's Lumber & Home Ctr, Inc
(304) 624-6549
515 Rosebud Plaza
Clarksburg, WV
 
Clarksburg - D
(304) 624-7171
102 Emily Dr
Clarksburg, WV
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Meadowbrook Mall
(304) 842-1400
225 Meadowbrook Rd
Bridgeport, WV
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:11-18
Store Features
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:11-18

Builders Service & Supply
(304) 265-3280
Country Club Road
Grafton, WV
 
Lowe's
(304) 624-7071
494 Emily Drive
Clarksburg, WV
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

LOWE'S OF CLARKSBURG, W. VA.
304 624-7071
494 EMILY DRIVE CLARKSBURG, WV, 26301
Clarksburg, WV
 
Ace Hardware
(304) 842-5491
414 Main St
Bridgeport, WV
 
Fairmont - Auth Hometown
(304) 366-6444
9803 Mall Loop Road
Fairmont, WV
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-19
Sun:12-17
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-19
Sun:12-17

Aultman True Value Hardware
(304) 363-6080
534 Virginia Avenue
Fairmont, WV
 

Tablesaw Extension

Tablesaw Extension

Make Wide Cuts in a Small Shop

By Roy Smith

There’s not enough room in my garage shop for a tablesaw with a 52-in.-capacity rip fence. But no worries—I don’t need one! To make wide cuts, I simply install a shop-made extension that bridges my saw to the wall—and doubles its 30-in. rip capacity! 

I made my extension by framing a piece of 3/4-in. mdf with rails on three sides. I covered the top of the extension—and the face of its fence—with plastic laminate. 

I attached U-shaped mounting brackets to the wall and the saw. The extension simply drops in place (see Fig. A ). I had to drill holes through the saw wing to mount the saw bracket. A cleat on the bottom of the extension wing hooks into the saw bracket. The wall brackets’s wide “U” makes it a bit easier to jockey the tablesaw into position, because it allows a little wiggle room.

I routed grooves in the extension to recess the T-track and the adhesive-backed rules. To calibrate the rules, I set the extension’s fence parallel to the blade and made a test cut. The width of the test piece now indicated the fence’s distance from the blade, so I used its measurement to install the rules. An L-shaped storage cleat mounted on the extension’s bottom allows storing the extension wing vertically. 

The extension installs easily. Its front and back rails capture the saw bracket to minimize movement.

Use both rules to set the fence. The rules are calibrated so the fence is parallel to the blade when both measurements match. 

The extension table stores on the wall. This flexibility frees shop space that would have been occupied by my saw if it had a super-wide-capacity rip fence. 

Source

Rockler, (800) 279-4441,www.rockler.com, 36033 Aluminum T-Track, 3/8” x 3/4” x 36”, $11 ea. 33965 1” T-Slot Bolt, $.79 ea. 71514 2” T-Knob, $1.29 ea. 69116 Left-to-Right Self Adhesive Rule, 6’, $8 ea.

This story originally appeared in  American Woodworker September 2007, issue #130.   

Source information may have changed since the original publication date.


September 2007, issue #130

Purchase this back issue.

Click here to read the rest of the article from American Woodworker