American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Tablesaw Extension Laconia NH

There’s not enough room in my garage shop for a tablesaw with a 52-in.-capacity rip fence. But no worries—I don’t need one! To make wide cuts, I simply install a shop-made extension that bridges my saw to the wall—and doubles its 30-in. rip capacity!

Goosebay Sawmill & Lumber
(603) 798-5135
83 Dover Road Route 4
Chichester, NH

Data Provided by:
Gilford Home Center
(603) 524-1692
32 Gilford East Dr
Gilford, NH
 
Belmont True Value Hardware
(603) 267-8510
131 Main St
Belmont, NH
 
Lowe's
(603) 729-2016
48 Lowes Drive
Tilton, NH
Hours
M-SA 7 am - 9 pm
SU 8 am - 7 pm

Alton True Value&country Sply
(603) 875-3241
Monument Sq - Main St
Alton, NH
 
True Value Hardware
(603) 524-1601
1084 Union Ave
Laconia, NH
 
Lowe's
(603) 556-6032
1407 Lakeshore Road
Gilford, NH
Hours
M-SA 6 am - 9 pm
SU 8 am - 7 pm

Bryant&lawrence True Value Hdw.
(603) 286-4322
268 Main St
Tilton, NH
 
Bay Supply True Value
(603) 569-1484
1 Bay St
Wolfeboro, NH
 
E M Heath True Value Hardware
(603) 253-4381
318 Whittier Highway
Center Harbor, NH
 
Data Provided by:

Tablesaw Extension

Tablesaw Extension

Make Wide Cuts in a Small Shop

By Roy Smith

There’s not enough room in my garage shop for a tablesaw with a 52-in.-capacity rip fence. But no worries—I don’t need one! To make wide cuts, I simply install a shop-made extension that bridges my saw to the wall—and doubles its 30-in. rip capacity! 

I made my extension by framing a piece of 3/4-in. mdf with rails on three sides. I covered the top of the extension—and the face of its fence—with plastic laminate. 

I attached U-shaped mounting brackets to the wall and the saw. The extension simply drops in place (see Fig. A ). I had to drill holes through the saw wing to mount the saw bracket. A cleat on the bottom of the extension wing hooks into the saw bracket. The wall brackets’s wide “U” makes it a bit easier to jockey the tablesaw into position, because it allows a little wiggle room.

I routed grooves in the extension to recess the T-track and the adhesive-backed rules. To calibrate the rules, I set the extension’s fence parallel to the blade and made a test cut. The width of the test piece now indicated the fence’s distance from the blade, so I used its measurement to install the rules. An L-shaped storage cleat mounted on the extension’s bottom allows storing the extension wing vertically. 

The extension installs easily. Its front and back rails capture the saw bracket to minimize movement.

Use both rules to set the fence. The rules are calibrated so the fence is parallel to the blade when both measurements match. 

The extension table stores on the wall. This flexibility frees shop space that would have been occupied by my saw if it had a super-wide-capacity rip fence. 

Source

Rockler, (800) 279-4441,www.rockler.com, 36033 Aluminum T-Track, 3/8” x 3/4” x 36”, $11 ea. 33965 1” T-Slot Bolt, $.79 ea. 71514 2” T-Knob, $1.29 ea. 69116 Left-to-Right Self Adhesive Rule, 6’, $8 ea.

This story originally appeared in  American Woodworker September 2007, issue #130.   

Source information may have changed since the original publication date.


September 2007, issue #130

Purchase this back issue.

Click here to read the rest of the article from American Woodworker