American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Tablesaw Extension Norfolk VA

There’s not enough room in my garage shop for a tablesaw with a 52-in.-capacity rip fence. But no worries—I don’t need one! To make wide cuts, I simply install a shop-made extension that bridges my saw to the wall—and doubles its 30-in. rip capacity!

Woodcraft - Norfolk/Virginia Beach, VA
(757) 466-1166
The Shops at Janaf, Suite 152
Norfolk, VA

Data Provided by:
The Home Depot
(757)461-6197
1261 N Military Hwy
Norfolk, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(757)340-5804
3352 Virginia Bch Blvd
Virginia Beach, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

AustralianBurls.com
(757) 816-5622
1013 Fairway Dr
Chesapeake, VA

Data Provided by:
The Home Depot
(757)471-4880
2020 Lynnhaven Pkwy
Virginia Beach, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(757) 461-6197
1261 N Military Hwy
Norfolk, VA
 
The Home Depot
(757)430-6872
2324 Elson Green Avenue
Virginia Beach, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(757)548-8478
1400 Tintern Lane
Chesapeake, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(757)465-9166
2421 Old Taylor Rd
Chesapeake, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(757)827-5121
1413 Armistead Ave
Hampton, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Tablesaw Extension

Tablesaw Extension

Make Wide Cuts in a Small Shop

By Roy Smith

There’s not enough room in my garage shop for a tablesaw with a 52-in.-capacity rip fence. But no worries—I don’t need one! To make wide cuts, I simply install a shop-made extension that bridges my saw to the wall—and doubles its 30-in. rip capacity! 

I made my extension by framing a piece of 3/4-in. mdf with rails on three sides. I covered the top of the extension—and the face of its fence—with plastic laminate. 

I attached U-shaped mounting brackets to the wall and the saw. The extension simply drops in place (see Fig. A ). I had to drill holes through the saw wing to mount the saw bracket. A cleat on the bottom of the extension wing hooks into the saw bracket. The wall brackets’s wide “U” makes it a bit easier to jockey the tablesaw into position, because it allows a little wiggle room.

I routed grooves in the extension to recess the T-track and the adhesive-backed rules. To calibrate the rules, I set the extension’s fence parallel to the blade and made a test cut. The width of the test piece now indicated the fence’s distance from the blade, so I used its measurement to install the rules. An L-shaped storage cleat mounted on the extension’s bottom allows storing the extension wing vertically. 

The extension installs easily. Its front and back rails capture the saw bracket to minimize movement.

Use both rules to set the fence. The rules are calibrated so the fence is parallel to the blade when both measurements match. 

The extension table stores on the wall. This flexibility frees shop space that would have been occupied by my saw if it had a super-wide-capacity rip fence. 

Source

Rockler, (800) 279-4441,www.rockler.com, 36033 Aluminum T-Track, 3/8” x 3/4” x 36”, $11 ea. 33965 1” T-Slot Bolt, $.79 ea. 71514 2” T-Knob, $1.29 ea. 69116 Left-to-Right Self Adhesive Rule, 6’, $8 ea.

This story originally appeared in  American Woodworker September 2007, issue #130.   

Source information may have changed since the original publication date.


September 2007, issue #130

Purchase this back issue.

Click here to read the rest of the article from American Woodworker