American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tablesaw Extension Oconomowoc WI

There’s not enough room in my garage shop for a tablesaw with a 52-in.-capacity rip fence. But no worries—I don’t need one! To make wide cuts, I simply install a shop-made extension that bridges my saw to the wall—and doubles its 30-in. rip capacity!

The Home Depot
(262)646-9160
3400 Hillside Dr
Delafield, WI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(262)717-0344
2320 W Bluemound Rd
Waukesha, WI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(262)363-7141
232 E Wolf Run
Mukwonago, WI
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Kmart 3692 / Cross Merch
(262) 567-2300
1450 Summit Avenue
Oconomowoc, WI
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Lorleberg True Value
(262) 567-0267
900 E Wisconsin Ave
Oconomowoc, WI
 
Boehm-Madisen Lumber Co.
(262) 544-4660
N16 W22100 Jericho Dr.
Waukesha, WI

Data Provided by:
Kettle Moraine Hardwoods
(262) 644-8119
5261 Aurora Rd.
Hartford, WI

Data Provided by:
The Home Depot
(262)502-9840
N94 W 18375 Thunder Rdg
Menomonee Falls, WI
Hours
Mon-Sat: 8:00am-8:00pm
Sun: 9:00am-6:00pm

Ace Hardware of Oconomowoc
(262) 567-8288
1081 Summit Ave
Oconomowoc, WI
 
Warden's Ace Hardware
(262) 646-4101
2835 Heritage Dr, walmart plaza shopping center
Delafield, WI
 
Data Provided by:

Tablesaw Extension

Tablesaw Extension

Make Wide Cuts in a Small Shop

By Roy Smith

There’s not enough room in my garage shop for a tablesaw with a 52-in.-capacity rip fence. But no worries—I don’t need one! To make wide cuts, I simply install a shop-made extension that bridges my saw to the wall—and doubles its 30-in. rip capacity! 

I made my extension by framing a piece of 3/4-in. mdf with rails on three sides. I covered the top of the extension—and the face of its fence—with plastic laminate. 

I attached U-shaped mounting brackets to the wall and the saw. The extension simply drops in place (see Fig. A ). I had to drill holes through the saw wing to mount the saw bracket. A cleat on the bottom of the extension wing hooks into the saw bracket. The wall brackets’s wide “U” makes it a bit easier to jockey the tablesaw into position, because it allows a little wiggle room.

I routed grooves in the extension to recess the T-track and the adhesive-backed rules. To calibrate the rules, I set the extension’s fence parallel to the blade and made a test cut. The width of the test piece now indicated the fence’s distance from the blade, so I used its measurement to install the rules. An L-shaped storage cleat mounted on the extension’s bottom allows storing the extension wing vertically. 

The extension installs easily. Its front and back rails capture the saw bracket to minimize movement.

Use both rules to set the fence. The rules are calibrated so the fence is parallel to the blade when both measurements match. 

The extension table stores on the wall. This flexibility frees shop space that would have been occupied by my saw if it had a super-wide-capacity rip fence. 

Source

Rockler, (800) 279-4441,www.rockler.com, 36033 Aluminum T-Track, 3/8” x 3/4” x 36”, $11 ea. 33965 1” T-Slot Bolt, $.79 ea. 71514 2” T-Knob, $1.29 ea. 69116 Left-to-Right Self Adhesive Rule, 6’, $8 ea.

This story originally appeared in  American Woodworker September 2007, issue #130.   

Source information may have changed since the original publication date.


September 2007, issue #130

Purchase this back issue.

Click here to read the rest of the article from American Woodworker