American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Tablesaw Extension Oshkosh WI

There’s not enough room in my garage shop for a tablesaw with a 52-in.-capacity rip fence. But no worries—I don’t need one! To make wide cuts, I simply install a shop-made extension that bridges my saw to the wall—and doubles its 30-in. rip capacity!

Woodcraft - Fox Cities/Appleton, WI
(920) 730-9663
4731 Michael's Drive
Appleton, WI

Data Provided by:
M. Schettl Sales Incorporated
(920) 426-1681
5105 County Road S
Oshkosh, WI
 
Lowe's
(920) 232-7423
1075 North Washburn Street
Oshkosh, WI
Hours
M-SA 6:30 am - 9 pm
SU 8 am - 7 pm

Kitz & Pfeil True Value Hdwe
(920) 236-3340
427 N Main St
Oshkosh, WI
 
LW Meyer- Neenah
(920) 722-4525
1375 Constitution Drive Neenah, WI, 54956
Neenah, WI
 
The Home Depot
(920)993-1123
653 N Westhill Blvd
Grand Chute, WI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Oshkosh - Auth Hometown
(920) 230-6777
2081 Witzel Avenue
Oshkosh, WI
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:10-20
Tue:10-20
Wed:10-20
Thu:10-20
Fri:10-20
Sat:9-18
Sun:11-16
Store Features
Mon:10-20
Tue:10-20
Wed:10-20
Thu:10-20
Fri:10-20
Sat:9-18
Sun:11-16

Lowe's of Oshkosh
920-232-7423
1075 North Washburn Street Oshkosh, WI, 54904
Oshkosh, WI
 
Brazee Ace Hardware
(920) 722-1113
516 N Commercial St
Neenah, WI
 
Krueger True Value
(920) 722-1588
999 Winneconne Ave
Neenah, WI
 
Data Provided by:

Tablesaw Extension

Tablesaw Extension

Make Wide Cuts in a Small Shop

By Roy Smith

There’s not enough room in my garage shop for a tablesaw with a 52-in.-capacity rip fence. But no worries—I don’t need one! To make wide cuts, I simply install a shop-made extension that bridges my saw to the wall—and doubles its 30-in. rip capacity! 

I made my extension by framing a piece of 3/4-in. mdf with rails on three sides. I covered the top of the extension—and the face of its fence—with plastic laminate. 

I attached U-shaped mounting brackets to the wall and the saw. The extension simply drops in place (see Fig. A ). I had to drill holes through the saw wing to mount the saw bracket. A cleat on the bottom of the extension wing hooks into the saw bracket. The wall brackets’s wide “U” makes it a bit easier to jockey the tablesaw into position, because it allows a little wiggle room.

I routed grooves in the extension to recess the T-track and the adhesive-backed rules. To calibrate the rules, I set the extension’s fence parallel to the blade and made a test cut. The width of the test piece now indicated the fence’s distance from the blade, so I used its measurement to install the rules. An L-shaped storage cleat mounted on the extension’s bottom allows storing the extension wing vertically. 

The extension installs easily. Its front and back rails capture the saw bracket to minimize movement.

Use both rules to set the fence. The rules are calibrated so the fence is parallel to the blade when both measurements match. 

The extension table stores on the wall. This flexibility frees shop space that would have been occupied by my saw if it had a super-wide-capacity rip fence. 

Source

Rockler, (800) 279-4441,www.rockler.com, 36033 Aluminum T-Track, 3/8” x 3/4” x 36”, $11 ea. 33965 1” T-Slot Bolt, $.79 ea. 71514 2” T-Knob, $1.29 ea. 69116 Left-to-Right Self Adhesive Rule, 6’, $8 ea.

This story originally appeared in  American Woodworker September 2007, issue #130.   

Source information may have changed since the original publication date.


September 2007, issue #130

Purchase this back issue.

Click here to read the rest of the article from American Woodworker