American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tablesaw Picture Frame Park City UT

Richard’s molding also simplifies assembly. Mitering and gluing odd-shaped picture frame molding can be a struggle. With this technique, the frame is mitered and glued when the stock still has its square profile. That makes building a picture frame much easier.

The Home Depot
(435)649-1467
1595 East Frontage Rd
Park City, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(801)619-6261
9570 S Highland Dr
Sandy, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(801)461-4248
3398 S Highland Drive
Salt Lake City, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Ace Hdw at Olympus Hills
(801) 424-1414
3939 Wasatch Blvd
Salt Lake City, UT
 
Kmart 4159 / Cross Merch
(801) 266-4437
4670 S 900 East
Salt Lake Cit, UT
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

The Home Depot
(801)567-0700
1310 E Park Centre Dr
Salt Lake City, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(801)763-8640
885 W Grassland Drive
American Fork, UT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Mortimer Lumber
810-987-3020
2307 Lapeer Ave Port Huron, MI, 84060
Port Huron, MI
 
Ace Hardware Lone Peak
(801) 763-2221
5353 W PARKWAY EAST ST
Highland, UT
 
ABC Supply Co.,Inc/Murray
801-281-3232
5602 S. 300 West Murray, UT, 84107
Murray, UT
 

Tablesaw Picture Frame

Tablesaw Picture Frame

Safely make shaper-quality molding on your tablesaw without fancy jigs.

by Eric Smith and Richard Tendick

This how-to story has a picture-perfect ending. In fact, you might want to round up some spectators for applause in the final steps. Richard Tendick has developed a safe, simple technique to help you make narrow, complex picture-frame stock using nothing more than a tablesaw. That’s right, there are no routers or specialized jigs and sleds to make, either. With Richard’s system, you actually glue the frame before the final cut. The fun comes when the frame is cut loose from the square stock. 

Richard’s molding also simplifies assembly. Mitering and gluing odd-shaped picture frame molding can be a struggle. With this technique, the frame is mitered and glued when the stock still has its square profile. That makes building a picture frame much easier. 

Grain and Color are Important

This technique requires 1-1/2-in. square stock. For a frame to look good, the grain must flow smoothly around all four pieces (see “Oops,” below) and the color must be consistent. Choose clear, straight-grained wood for your frame stock. It’s best if you can cut the frame stock from a single length of wood. Buy extra wood for test cuts. We found 1-1/2-in. square oak stair balusters sold at home centers to be an excellent source for frame stock. 

Set Up for the Cuts 

1. Rough-cut the frame stock to a few inches over the finished dimensions for cutting on the tablesaw. 

2. Sketch the cuts on the end of each piece for orientation (Photo 1; Fig. A). All cuts start at the same end, so if you find yourself reversing the piece, something is wrong. Pay attention to grain direction! (See Fig. A and “Oops.”)

3. Cut spacer strips 3/8, 5/8 and 3/4 in. wide by 18 in. long. You’ll use these for setting the fence and saw blade height for some of the cuts.

 Making the Saw Cuts

4. Set the blade to make a 3/8-in.-deep cut and make Cut 1 (Fig. A, below). 

5. Set the blade and fence for Cut 2 (Photo 2) and make the cut. 

6. Make Cut 3 with the blade titled to 33 degrees. Set the blade just high enough to poke through the wood about 1/4 in. (Photo 3). 

7. Make Cut 4 to create the rabbet that holds your picture, matte and glass (Photo 4). Set the fence and blade height using Cut 1 as a reference. 

Sanding, Mitering and Gluing

8. Sand the frame before cutting the miters (Photo 5). It’s a lot easier than sanding into the corners of an assembled frame. 

9. Before you cut the miters, take a 1/2-in.-thick slice off your stock. Save the slice for setting up the last cut. 

10. Attach a long subfence to the miter gauge. Use a drafting square to set the gauge at 45 degrees. (see “Tips for Perfect Miters,” AW #108, July 2004). 

11. Cut the miters (Photos 6 and 7).

Click here to read the rest of the article from American Woodworker