American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tablesawn Circles Aztec NM

It's easy to cut perfectly round tabletops of almost any size on your tablesaw. All it takes is a simple jig and careful setup. With this method, you can safely cut dia-meters from 12 in. to within an inch of your saw's rip-fence capacity.

The Home Depot
(505)327-0710
3560 E Main Street
Farmington, NM
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 7:00am-8:00pm

Kmart 7035 / Cross Merch
(505) 327-3352
3000 E Main St
Farmington, NM
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Animas Vly Mall
(505) 324-3200
4601 E Main St
Farmington, NM
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Ace Hdw of Farmington
(505) 327-3491
3030 E Main St Ste F, across from Hastings
Farmington, NM
 
Big R Of Farmington
(505) 326-7711
908 East Main St
Farmington, NM
 
Bloomfield Ace Hardware
(505) 632-8620
1947 W Broadway
Bloomfield, NM
 
Lowe's
(505) 599-0200
5451 East Pinon Hills Boulevard
Farmington, NM
Hours
M-SA 6 am - 9 pm
SU 8 am - 8 pm

LOWE'S OF FARMINGTON, NM
505 599-0200
5451 EAST PINON HILLS BLVD. FARMINGTON, NM, 87402
Farmington, NM
 
Doghouse Manufacturing And Sup
(505) 325-4110
1201 Dowel Road
Farmington, NM
 
The Home Depot
(505)726-2362
530 Kachina Street
Gallup, NM
Hours
Mon-Sat: 7:00am-9:00pm
Sun: 8:00am-7:00pm

Tablesawn Circles

Tablesawn Circles



It's easy to cut perfectly round tabletops of almost any size on your tablesaw. All it takes is a simple jig (Fig A) and careful setup. With this method, you can safely cut dia-meters from 12 in. to within an inch of your saw's rip-fence capacity.

Why use a tablesaw? It's better than bandsawing or routing, especially for large-diameter circles. Unlike bandsawing, when you're working on the tablesaw, the blank is fully supported, so it's easy to control. Unlike routing, you stay in one place while making the cut and you don't have to deal with a tangle-prone cord. Tablesawn results are better, too. The circular blade leaves a cleaner edge than a bandsaw blade does and it won't tear out the end grain, the way a router bit can.

This tablesaw technique is similar to the approach used for cutting circles on a bandsaw. Using a clamped-on jig with a center pin, you make the cut by rotating the blank into the blade. Unlike the bandsaw method, however, you must start with a blank that's already roughsawn. Cutting the circle to final size takes several steps. Like turning a rough blank into a round on a lathe, you gradually cut down the high spots until the blank is perfectly round. Here's how to do it:

1. Draw the circle on the bottom of the blank, using a compass or trammel.

2. Use a jigsaw to rough-saw the blank 1/4 in. to 1/2 in. larger than the final diameter. Starting on the bottom face, draw a diameter line that continues all the way around the blank.

3. Enlarge the center hole that remains from drawing the circle to fit the jig's center pin. Mount the blank (Photo 1). Then install the retainers.

4. Before you position the jig, unplug your saw and install an alternate tooth bevel (ATB) blade with at least 40 teeth. Raise the blade fully. Set the rip fence so there's just enough room for the jig and blank to slide past the blade. Align the blank's centerline with the reference line you've drawn on the clamp rail (Fig. A).

5. Hold the jig against the fence, slide it forward into position and clamp it securely (Photo 2).

6. Lower the blade fully to locate the jig for the first cut. Spin the roughsawn blank to find its widest spot. Then reset the fence so the blade will remove about 1/16 in. from this point. A more aggressive cut wouldn't work; it would cause binding between the blank and the blade.

PHOTO 1:
Mount the rough sawn blank on the jig. It rotates on the center pin. Align the blank's centerline with the reference line on the jig's rail.
PHOTO 2:
Clamp the jig to the rip fence at the point where the tip of the fully raised blade, the top edge of the blank and the centerline meet. Lower the blade completely. Then position the blank for the first cut by adjusting the fence.

7. Start the cut by raising the blade (Photo 3). Then rotate the blank clockwise (Photo 4). Shut...

Click here to read the rest of the article from American Woodworker