American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tablesawn Circles Billings MT

It's easy to cut perfectly round tabletops of almost any size on your tablesaw. All it takes is a simple jig and careful setup. With this method, you can safely cut dia-meters from 12 in. to within an inch of your saw's rip-fence capacity.

A & H Turf & Specialties, Inc.
(406) 245-8466
468 South Moore Lane
Billings, MT

Data Provided by:
Fastenal- Billings
406-252-9090
1518 1st Ave N Billings, MT, 59101
Billings, MT
 
Aldrich And Company
(406) 259-5531
2021 4th Ave North
Billings, MT
 
Western Tool Supply- Billings
406-652-4797
3088 Gabel Road Billings, MT, 59102
Billings, MT
 
King's Ace Hardware
(406) 656-1445
2264 Central Ave
Billings, MT
 
The Home Depot
(406)655-9038
2784 King Ave West
Billings, MT
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Kings Ace Hardware
(406) 245-0070
4170 State Ave
Billings, MT
 
Lowe's
(406) 655-9317
2717 King Avenue West
Billings, MT
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Billings - D
(406) 656-5700
2424 Central Ave
Billings, MT
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

LOWE'S OF BILLINGS, MT.
406 655-9317
2717 KING AVENUE WEST BILLINGS, MT, 59102
Billings, MT
 
Data Provided by:

Tablesawn Circles

Tablesawn Circles



It's easy to cut perfectly round tabletops of almost any size on your tablesaw. All it takes is a simple jig (Fig A) and careful setup. With this method, you can safely cut dia-meters from 12 in. to within an inch of your saw's rip-fence capacity.

Why use a tablesaw? It's better than bandsawing or routing, especially for large-diameter circles. Unlike bandsawing, when you're working on the tablesaw, the blank is fully supported, so it's easy to control. Unlike routing, you stay in one place while making the cut and you don't have to deal with a tangle-prone cord. Tablesawn results are better, too. The circular blade leaves a cleaner edge than a bandsaw blade does and it won't tear out the end grain, the way a router bit can.

This tablesaw technique is similar to the approach used for cutting circles on a bandsaw. Using a clamped-on jig with a center pin, you make the cut by rotating the blank into the blade. Unlike the bandsaw method, however, you must start with a blank that's already roughsawn. Cutting the circle to final size takes several steps. Like turning a rough blank into a round on a lathe, you gradually cut down the high spots until the blank is perfectly round. Here's how to do it:

1. Draw the circle on the bottom of the blank, using a compass or trammel.

2. Use a jigsaw to rough-saw the blank 1/4 in. to 1/2 in. larger than the final diameter. Starting on the bottom face, draw a diameter line that continues all the way around the blank.

3. Enlarge the center hole that remains from drawing the circle to fit the jig's center pin. Mount the blank (Photo 1). Then install the retainers.

4. Before you position the jig, unplug your saw and install an alternate tooth bevel (ATB) blade with at least 40 teeth. Raise the blade fully. Set the rip fence so there's just enough room for the jig and blank to slide past the blade. Align the blank's centerline with the reference line you've drawn on the clamp rail (Fig. A).

5. Hold the jig against the fence, slide it forward into position and clamp it securely (Photo 2).

6. Lower the blade fully to locate the jig for the first cut. Spin the roughsawn blank to find its widest spot. Then reset the fence so the blade will remove about 1/16 in. from this point. A more aggressive cut wouldn't work; it would cause binding between the blank and the blade.

PHOTO 1:
Mount the rough sawn blank on the jig. It rotates on the center pin. Align the blank's centerline with the reference line on the jig's rail.
PHOTO 2:
Clamp the jig to the rip fence at the point where the tip of the fully raised blade, the top edge of the blank and the centerline meet. Lower the blade completely. Then position the blank for the first cut by adjusting the fence.

7. Start the cut by raising the blade (Photo 3). Then rotate the blank clockwise (Photo 4). Shut...

Click here to read the rest of the article from American Woodworker