Tapered Sliding Dovetails Jackson NJ
M-SA 6 am - 10 pm
SU 8 am - 7 pm
M-SA 6 am - 9 pm
SU 8 am - 7 pm
E Windsor, NJ
New Egypt, NJ
Tapered Sliding Dovetails
Tapered Sliding Dovetails
Two jigs make a complicated joint ever so easy.
by Luke Hartle
The tapered sliding dovetail joint is one of the hallmarks of fine craftsmanship. But making it has made many craftsmen pull out their hair! I’ve made it simple, using a jig with a micro-adjust feature for dialing in a perfect fit.
This exceptionally strong joint was traditionally used to bind solid shelves and dividers to the sides of a carcase. A standard sliding dovetail must overcome a lot of friction to go home, but a tapered sliding dovetail is a cinch to assemble. My bookcase on page 70 makes full use of it, additionally joining the top to the sides. The jigs I built are sized to fit the bookcase, but it’s easy to tailor them to another project.
To reduce setup time, I used two routers to make the joint, but that’s not absolutely necessary. You’ll need a 1/2-in. top-bearing dovetail bit ($34), a 1/2-in. top-bearing flush-trim bit ($29), a 3/8-in. straight bit ($23) and a 5/8-in.-dia. template guide.
Build the Tail Jig
1. Make a taper template for routing the tails. First, draw a rectangle (shown in red in Photo 1) the same size as the end of the board that receives the tail. Next, draw two lines (shown in black) inside the rectangle indicating the amount the dovetail will taper (Fig. A, below). Each side of this taper has a 1/8-in. rise over the joint’s 11-in. length, or run. A 1/8-in. rise works equally well if the joint is a few inches shorter or longer. Rough-cut the template 1/16 in. outside the black lines with your bandsaw.
2. Cut to the black lines on the router table (Photo 2), using a top-bearing straight bit (see Sources, below). Fasten the template to the guide board with screws so the template doesn’t flex.
3. Screw the template to a test board (Photo 3). Align the red lines with the board’s edges. Position the template so it’s exactly centered from side to side, clamp it in place and drive in the screws.
4. Assemble the rest of the jig on the test board so it fits tightly (Photo 4). Clamp the braces (C) in place first; then add the ends (B, Fig. B, below).
5. Add two outriggers (D, Photo 5). Stand the jig on a flat surface to ensure these boards are level with the template.
6. Rout a test dovetail with a bearing-guided router bit (Photo 6; see Sources, below). Lower the bit so it cuts 1/2 in. into the test piece. Unscrew the template and remove the jig.
Build the Socket Jig
7. Build this jig around a second test board (Photo 7). To position the fixed guide board, use the same 1/8-in. taper you used to make the tail jig. Draw an alignment mark (shown in red) on the guide board perpendicular to the test board’s edge. Lay the fixed guide board exactly on the line at one end and offset it by 1/8 in. at the other end. Fasten the guide board to the braces (G). The spacer enables this jig to fit the 12-in. top of the &ldq...
Philadelphia Flower Show 2018
Dates: 3/4/2018 – 3/11/2018
Pennsylvania Convention Center Philadelphia
1101 Arch Street
The Philadelphia Flower Show, internationally recognized as one of the nation's premiere events as well as the oldest and largest indoor show of its kind, is produced by the Pennsylvania Horticultural Society. PHS has more than 15,000 members throughout the country, offers hundreds of educational programs year-round, and is considered the nationâ�TMs leading authority on urban renewal through greening. PHS's acclaimed Philadelphia Green program restores neighborhood parks, creates community gardens, conducts large scale tree plantings, revitalizes vacant land, engages thousands of citizens in community development activities and maintains treasured public landscapes. Its greening efforts are modeled in many cities across the country.Not sure if you want to exhibit at or attend the Philadelphia Flower Show 2018? See the panels below to get the information you need to make an informed decision.All information in Events In America is deemed to be accurate at the time we add it,and we take steps to verify all details and update our records when new information is provided, but as people, events and circumstances change, we caution users to independently confirm all information. EventsInAmerica.com and Events In America LLC make no guarantee of accuracy and assume no liability for inaccurate information.