American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tapered Sliding Dovetails Kailua Kona HI

The tapered sliding dovetail joint is one of the hallmarks of fine craftsmanship. But making it has made many craftsmen pull out their hair! I’ve made it simple, using a jig with a micro-adjust feature for dialing in a perfect fit.

The Home Depot
(808)326-6013
73-5598 Olowalu St
Kailua Kona, HI
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-6:00pm

LOWE'S OF KONA, HI
808 331-3470
75-5677 HALE KAPILI STREET KAILUA KONA, HI, 96740
Kailua Kona, HI
 
HPM Bldg Sply/Kailua-Kona
74-5511 Luhia Street Kailua-Kona, HI, 96740
Kailua-Kona, HI
 
Fastenal- Lailua Kona
808-329-7092
73-5569 Maiau St #105 & #106 Kailua Kona, HI, 96740
Kailua Kona, HI
 
HPM Building Supply
(808) 329-1634
74-5511 Luhia St
Kailua Kona, HI
 
Kmart 7683 / Cross Merch
(808) 326-2331
74-5465 Kamaka'Eha Ave
Kailua-Kona, HI
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

ABC Supply Co.,Inc/Kailua Kona
808-327-0445
73-4939 Kamanu St. Kailua Kona, HI, 96740
Kailua Kona, HI
 
Kona Ace Hdwe & Crafts
(808) 329-2981
74-5500 Kaiwi St
Kailua Kona, HI
 
Lowe's
(808) 331-3470
75-5677 Hale Kapili Street
Kailua Kona, HI
Hours
M-SA 6 am - 9 pm
SU 7 am - 8 pm

CAPTAIN COOK ACE HARDWARE
(808) 323-2655
KEALAKEKUA RANCH CENTER
CAPTAIN COOK, HI
 

Tapered Sliding Dovetails

Tapered Sliding Dovetails

Two jigs make a complicated joint ever so easy.

by Luke Hartle

The tapered sliding dovetail joint is one of the hallmarks of fine craftsmanship. But making it has made many craftsmen pull out their hair! I’ve made it simple, using a jig with a micro-adjust feature for dialing in a perfect fit.

This exceptionally strong joint was traditionally used to bind solid shelves and dividers to the sides of a carcase. A standard sliding dovetail must overcome a lot of friction to go home, but a tapered sliding dovetail is a cinch to assemble. My bookcase on page 70 makes full use of it, additionally joining the top to the sides. The jigs I built are sized to fit the bookcase, but it’s easy to tailor them to another project. 

To reduce setup time, I used two routers to make the joint, but that’s not absolutely necessary. You’ll need a 1/2-in. top-bearing dovetail bit ($34), a 1/2-in. top-bearing flush-trim bit ($29), a 3/8-in. straight bit ($23) and a 5/8-in.-dia. template guide. 

Build the Tail Jig

1. Make a taper template for routing the tails. First, draw a rectangle (shown in red in Photo 1) the same size as the end of the board that receives the tail. Next, draw two lines (shown in black) inside the rectangle indicating the amount the dovetail will taper (Fig. A, below). Each side of this taper has a 1/8-in. rise over the joint’s 11-in. length, or run. A 1/8-in. rise works equally well if the joint is a few inches shorter or longer. Rough-cut the template 1/16 in. outside the black lines with your bandsaw.

2. Cut to the black lines on the router table (Photo 2), using a top-bearing straight bit (see Sources, below). Fasten the template to the guide board with screws so the template doesn’t flex.

3. Screw the template to a test board (Photo 3). Align the red lines with the board’s edges. Position the template so it’s exactly centered from side to side, clamp it in place and drive in the screws. 

4. Assemble the rest of the jig on the test board so it fits tightly (Photo 4). Clamp the braces (C) in place first; then add the ends (B, Fig. B, below).

5. Add two outriggers (D, Photo 5). Stand the jig on a flat surface to ensure these boards are level with the template.

6. Rout a test dovetail with a bearing-guided router bit (Photo 6; see Sources, below). Lower the bit so it cuts 1/2 in. into the test piece. Unscrew the template and remove the jig.

Build the Socket Jig

7. Build this jig around a second test board (Photo 7). To position the fixed guide board, use the same 1/8-in. taper you used to make the tail jig. Draw an alignment mark (shown in red) on the guide board perpendicular to the test board’s edge. Lay the fixed guide board exactly on the line at one end and offset it by 1/8 in. at the other end. Fasten the guide board to the braces (G). The spacer enables this jig to fit the 12-in. top of the &ldq...

Click here to read the rest of the article from American Woodworker