American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tapered Sliding Dovetails Scottsbluff NE

The tapered sliding dovetail joint is one of the hallmarks of fine craftsmanship. But making it has made many craftsmen pull out their hair! I’ve made it simple, using a jig with a micro-adjust feature for dialing in a perfect fit.

The Home Depot
(308)630-2398
3102 Avenue I
Scottsbluff, NE
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

Murdoch's Ranch & Home Supply
(308) 220-3500
1510 E 20th St
Scottsbluff, NE
 
Carr Trumbull Do it center
(308) 632-2143
1310 Circle Dr
Scottsbluff, NE
 
The Home Depot
(402)333-9477
12710 L Street
Omaha, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(308)389-3515
911 Allen Drive
Grand Island, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Kmart 7024 / Cross Merch
(308) 632-3232
802 E 27Th St
Scottsbluff, NE
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Scottsbluff - Auth Hometown
(308) 632-7143
1615 Broadway
Scottsbluff, NE
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17

The Home Depot
(402)964-9700
3950 North 144th St
Omaha, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(308)630-2398
3102 Avenue I
Scottsbluff, NE
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

The Home Depot
(402)328-9669
6800 South 70th Street
Lincoln, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Tapered Sliding Dovetails

Tapered Sliding Dovetails

Two jigs make a complicated joint ever so easy.

by Luke Hartle

The tapered sliding dovetail joint is one of the hallmarks of fine craftsmanship. But making it has made many craftsmen pull out their hair! I’ve made it simple, using a jig with a micro-adjust feature for dialing in a perfect fit.

This exceptionally strong joint was traditionally used to bind solid shelves and dividers to the sides of a carcase. A standard sliding dovetail must overcome a lot of friction to go home, but a tapered sliding dovetail is a cinch to assemble. My bookcase on page 70 makes full use of it, additionally joining the top to the sides. The jigs I built are sized to fit the bookcase, but it’s easy to tailor them to another project. 

To reduce setup time, I used two routers to make the joint, but that’s not absolutely necessary. You’ll need a 1/2-in. top-bearing dovetail bit ($34), a 1/2-in. top-bearing flush-trim bit ($29), a 3/8-in. straight bit ($23) and a 5/8-in.-dia. template guide. 

Build the Tail Jig

1. Make a taper template for routing the tails. First, draw a rectangle (shown in red in Photo 1) the same size as the end of the board that receives the tail. Next, draw two lines (shown in black) inside the rectangle indicating the amount the dovetail will taper (Fig. A, below). Each side of this taper has a 1/8-in. rise over the joint’s 11-in. length, or run. A 1/8-in. rise works equally well if the joint is a few inches shorter or longer. Rough-cut the template 1/16 in. outside the black lines with your bandsaw.

2. Cut to the black lines on the router table (Photo 2), using a top-bearing straight bit (see Sources, below). Fasten the template to the guide board with screws so the template doesn’t flex.

3. Screw the template to a test board (Photo 3). Align the red lines with the board’s edges. Position the template so it’s exactly centered from side to side, clamp it in place and drive in the screws. 

4. Assemble the rest of the jig on the test board so it fits tightly (Photo 4). Clamp the braces (C) in place first; then add the ends (B, Fig. B, below).

5. Add two outriggers (D, Photo 5). Stand the jig on a flat surface to ensure these boards are level with the template.

6. Rout a test dovetail with a bearing-guided router bit (Photo 6; see Sources, below). Lower the bit so it cuts 1/2 in. into the test piece. Unscrew the template and remove the jig.

Build the Socket Jig

7. Build this jig around a second test board (Photo 7). To position the fixed guide board, use the same 1/8-in. taper you used to make the tail jig. Draw an alignment mark (shown in red) on the guide board perpendicular to the test board’s edge. Lay the fixed guide board exactly on the line at one end and offset it by 1/8 in. at the other end. Fasten the guide board to the braces (G). The spacer enables this jig to fit the 12-in. top of the &ldq...

Click here to read the rest of the article from American Woodworker