American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Teak Coffee Table Holt MI

With the resurgence of the mid-century Modern style in furniture, I thought I’d have some fun with this classic little coffee table. I used teak because it was the wood of choice for the Danish Modern style in the 1960s and 1970s. The same can be said for the round tapered legs and the soft, rounded edges and corners on the top.

The Home Depot
(517)381-0650
1749 Newman Rd
Okemos, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Johnson's Workbench
(517) 543-2727
563 N Cochran Ave
Charlotte, MI

Data Provided by:
Ace Hardware of Holt
(517) 694-3575
1960 Cedar St, Edru skate rink
Holt, MI
 
Apco Inc.
(517) 882-2455
5511 Enterprise Dr
Lansing, MI
 
LOWE'S OF S. LANSING, MI
517 699-2940
6821 SOUTH CEDAR STREET LANSING, MI, 48911
Lansing, MI
 
The Home Depot
(517)323-0229
936 S Waverly Rd
Lansing, MI
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

PARKER LUMBER
(517) 543-7068
760 S. Stine Road
Charlotte, MI

Data Provided by:
Kmart 4382 / Cross Merch
(517) 393-8770
5400 Cedar St S
Lansing, MI
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Lowe's
(517) 699-2940
6821 South Cedar Street
Lansing, MI
Hours
M-SA 7 am - 10 pm
SU 8 am - 8 pm

Ace Hardware
(517) 676-4900
340 S Cedar St
Mason, MI
 
Data Provided by:

Teak Coffee Table

Provided By:

Teak Coffee Table

A retro table with sleek lines and soft edges

by Bruce Kieffer

With the resurgence of the mid-century Modern style in furniture, I thought I’d have some fun with this classic little coffee table. I used teak because it was the wood of choice for the Danish Modern style in the 1960s and 1970s.  The same can be said for the round tapered legs and the soft, rounded edges and corners on the top.

The impressive, curved, solid-wood edging on the table  looks more difficult to make than it is (see “ Curved Corner Edging ”). After the top is done, building the rest of the table couldn’t be easier. Just turn four round tapered legs, attach them directly to the table with screw-on leg plates and you’re done.

I’ll show you a nifty turner’s technique for ensuring an even taper on each leg. If you don’t own a lathe, an alternative to turning is to make square tapered legs and use a 1/2-in. round-over bit on all four edges. Use a block plane and sandpaper to complete the round shape of the leg.

Make the Top

1. Cut the tabletop (A, Fig. A, below), edging pieces (B, C and D) and splines (E, F and G) to size. Shape, fit and attach the edgings to the top as described in “ Curved Corner Edging ”.

2. Rout the round-over edges and finish-sand the top. Be careful on that veneer—it’s paper thin. 

Turn the Legs

3. Mill the leg blanks (H) and cut them 1/2 in. extra long. The extra length is used to hold the leg at the tailstock end of the lathe. You’ll cut it off after the leg is turned.

4. Before you turn the legs, make them hexagonal by chamfering the corners on a bandsaw or tablesaw. Removing the waste gives you a head start on turning squares into cylinders.

5. Mount a leg blank between the centers of your lathe. Turn the blank to a 1-3/4-in.-dia. cylinder with a roughing gouge. 

6. Make a leg taper gauge from some MDF scrap (Photo 1; Fig. B, above). Lay out the leg taper and the 1/8-in.-wide parting diameter lines and cut the tapered profile on the bandsaw. Now you have a quick reference gauge for setting your calipers. 

7. Turn on the lathe and hold up the gauge to the leg. With a pencil, transfer the parting lines from the gauge to the blank.  

8. Use a parting tool and calipers to cut each groove to the proper depth (Photo 2). 

9. Rough out the tapered shape of the leg using the bottom of the grooves as a depth guide (Photo 3). Finish shaping the leg using a wide, square nose scraper.

10. Smooth the leg with sandpaper and a sanding block. Part the leg deeply at the bottom. Use a handsaw to remove the bottom waste. Hand-sand the leg with the grain to remove cross-grain scratches.

Assemble the Table

11. Drill 15/64-in. pilot holes in the legs and insert the hanger bolts (Photo 4). 

12. Mount the angled leg plates (Fig. A, Det. 1, page 70). You may need to drill shallow relief holes in the undersi...

Click here to read the rest of the article from American Woodworker