American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Teak Coffee Table Yakima WA

With the resurgence of the mid-century Modern style in furniture, I thought I’d have some fun with this classic little coffee table. I used teak because it was the wood of choice for the Danish Modern style in the 1960s and 1970s. The same can be said for the round tapered legs and the soft, rounded edges and corners on the top.

The Home Depot
(509)452-3016
2115 S First Street
Yakima, WA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Hometown Ace Hardware
(509) 972-4400
3700 Tieton Dr, Tieton Village Shopping Center
Yakima, WA
 
Modern Staple Inc- Yakima
(800) 562-7967
5010 W Chestnut Avenue Yakima, WA, 98908
Yakima, WA
 
Kmart 4439 / Cross Merch
(509) 248-1990
2304 E Nob Hill Blvd
Yakima, WA
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Western Tool Supply- Union Gap
509-574-4323
1901 South 14th Street Union Gap, WA, 98903
Union Gap, WA
 
Roy's Ace Hardware
(509) 453-4725
405 W Yakima Ave
Yakima, WA
 
Stein's Hardware
(509) 965-2622
7200 W Nob Hill Blvd, Meadowbrook Mall
Yakima, WA
 
Inland Fastening Systems- Yakima
509-952-6245
302 S First Street Yakima, WA, 98901
Yakima, WA
 
LOWE'S OF UNION GAP, WA.
509 248-3032
2500 RUDKIN ROAD UNION GAP, WA, 98903
Union Gap, WA
 
Valley Mall
(509) 576-9200
9 E Valley Mall Blvd
Union Gap, WA
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:11-18

Teak Coffee Table

Provided By:

Teak Coffee Table

A retro table with sleek lines and soft edges

by Bruce Kieffer

With the resurgence of the mid-century Modern style in furniture, I thought I’d have some fun with this classic little coffee table. I used teak because it was the wood of choice for the Danish Modern style in the 1960s and 1970s.  The same can be said for the round tapered legs and the soft, rounded edges and corners on the top.

The impressive, curved, solid-wood edging on the table  looks more difficult to make than it is (see “ Curved Corner Edging ”). After the top is done, building the rest of the table couldn’t be easier. Just turn four round tapered legs, attach them directly to the table with screw-on leg plates and you’re done.

I’ll show you a nifty turner’s technique for ensuring an even taper on each leg. If you don’t own a lathe, an alternative to turning is to make square tapered legs and use a 1/2-in. round-over bit on all four edges. Use a block plane and sandpaper to complete the round shape of the leg.

Make the Top

1. Cut the tabletop (A, Fig. A, below), edging pieces (B, C and D) and splines (E, F and G) to size. Shape, fit and attach the edgings to the top as described in “ Curved Corner Edging ”.

2. Rout the round-over edges and finish-sand the top. Be careful on that veneer—it’s paper thin. 

Turn the Legs

3. Mill the leg blanks (H) and cut them 1/2 in. extra long. The extra length is used to hold the leg at the tailstock end of the lathe. You’ll cut it off after the leg is turned.

4. Before you turn the legs, make them hexagonal by chamfering the corners on a bandsaw or tablesaw. Removing the waste gives you a head start on turning squares into cylinders.

5. Mount a leg blank between the centers of your lathe. Turn the blank to a 1-3/4-in.-dia. cylinder with a roughing gouge. 

6. Make a leg taper gauge from some MDF scrap (Photo 1; Fig. B, above). Lay out the leg taper and the 1/8-in.-wide parting diameter lines and cut the tapered profile on the bandsaw. Now you have a quick reference gauge for setting your calipers. 

7. Turn on the lathe and hold up the gauge to the leg. With a pencil, transfer the parting lines from the gauge to the blank.  

8. Use a parting tool and calipers to cut each groove to the proper depth (Photo 2). 

9. Rough out the tapered shape of the leg using the bottom of the grooves as a depth guide (Photo 3). Finish shaping the leg using a wide, square nose scraper.

10. Smooth the leg with sandpaper and a sanding block. Part the leg deeply at the bottom. Use a handsaw to remove the bottom waste. Hand-sand the leg with the grain to remove cross-grain scratches.

Assemble the Table

11. Drill 15/64-in. pilot holes in the legs and insert the hanger bolts (Photo 4). 

12. Mount the angled leg plates (Fig. A, Det. 1, page 70). You may need to drill shallow relief holes in the undersi...

Click here to read the rest of the article from American Woodworker