American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Techniques for Tighter, Faster, Stronger Miter Joints Mansfield TX

When you're building a box or frame, the opposite sides must be precisely the same length. Otherwise, even the most perfect miters won't form a tight joint.

The Home Depot
(817)453-4038
1725 N US Hwy 287
Mansfield, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #27
(817) 417-0070
4624 South Cooper St.
Arlington, TX

Data Provided by:
The Home Depot
(817)447-6602
300 NW John Jones
Burleson, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)459-4300
201 Rd To Six Flags West
Arlington, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)293-0343
7950 I-35 W South Fwy
Fort Worth, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)468-4224
4611 S Cooper St
Arlington, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(972)602-9385
5280 South Hwy 360
Grand Prairie, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(972)299-9390
373 E Fm 1382
Cedar Hill, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(817)496-3212
1151 Bridgewood Dr
Fort Worth, TX
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Brazos Forest Products - Grand Prairie
(972) 602-1225
2760 N Great SW Parkway
Grand Prairie, TX

Data Provided by:
Data Provided by:

Techniques for Tighter, Faster, Stronger Miter Joints

Techniques for Tighter, Faster, Stronger Miter Joints


Miter joints provide one main advantage over other joints: A miter joint hides end grain and brings face grain neatly together. Everything else about miter joints is a hassle. They're fussy, time-consuming and easy to screw up. But there are ways to minimize those hassles.

The 60-Second Squeeze
When you're dealing with small or hard-to-clamp parts, the best clamping tools might be your hands. Simply apply glue to the parts; then rub them together to distribute and tack-set the glue. Hold the parts together on a flat surface for 30 to 60 seconds (although it may seem like 5 minutes). Watch the joint as you release pressure; if anything moves, squeeze and hold for a few more seconds. Let the assembly sit undisturbed for a half-hour before you handle it again.

Make Micro Adjustments with a Disc Sander
No tool can tweak a miter's fit as easily as a disc sander can. You can shorten the workpiece a hair with a quick touch of the disc. You can also adjust the angle by a fraction of a degree. Instead of fussing with the miter gauge, make tiny adjustments by sticking a paper shim between the gauge and the workpiece. Knock-Off Blocks for Long Miters
Long miters are a nightmare to clamp, but adding temporary triangular blocks makes it a snap. The key is to use paper from a grocery bag. Dab some wood glue on both sides of the paper, stick the blocks wherever you need them and let the glue set overnight. When you're done clamping, remove each block with a hammer blow. The paper creates a weak spot in the glue bond, so the blocks break away without damage to the wood. Use hot water to soften any paper or glue left on the wood, then scrape it away and sand as usual. Customize a Drafting Square
Drafting squares are inexpensive, accurate and great for tool or jig setup. Because they're plastic, you can easily customize them to suit the job. We filed notches in this square to keep the saw teeth from interfering with setup. Drafting squares are available in various sizes for $4 to $10 at art and office supply stores. Guides for Perfect Edging
Mitered guides clamped in place let you perfect the length and angle of mitered edging. Use the edging stock itself to guide the fit of each piece. Clamp the guides precisely in place and work your way around the tabletop, gluing each perfected piece in place as you go. After you glue and clamp a section of banding, remove the adjoining guides immediately so you don't accidentally glue them in place.

The Touch Test
When you're building a box or frame, the opposite sides must be precisely the same length. Otherwise, even the most perfect miters won't form a tight joint. To compare lengths, hold the parts together on a flat surface and feel the ends. Your finger can detect differences your eyes c...

Click here to read the rest of the article from American Woodworker