American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Techniques for Tighter, Faster, Stronger Miter Joints Papillion NE

When you're building a box or frame, the opposite sides must be precisely the same length. Otherwise, even the most perfect miters won't form a tight joint.

The Home Depot
(402)331-2879
712 N Washington St
Papillion, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-7:00pm

The Home Depot
(402)573-6393
4545 North 72nd Street
Omaha, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(712)366-7814
3101 Manawa Center Dr
Council Bluffs, IA
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Lowe's
(402) 516-0968
8707 South 71St Plaza
Papillion, NE
Hours
M-SA 7 am - 10 pm
SU 8 am - 8 pm

Carlson Systems- La Vista
(402) 951-5999
7003 S 109th Street La Vista, NE, 68128
La Vista, NE
 
The Home Depot
(402)333-9477
12710 L Street
Omaha, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(402)964-9700
3950 North 144th St
Omaha, NE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Papillion
402-597-0275
705 N. Frontier Dr Papillion, NE, 68046
Papillion, NE
 
Cj's Home Center
(402) 331-1638
8018 Harrison Street
Ralston, NE
 
Lowe's of Papillion, NE
402-516-0968
8707 South 71st Plaza Omaha, NE, 68157
Omaha, NE
 

Techniques for Tighter, Faster, Stronger Miter Joints

Techniques for Tighter, Faster, Stronger Miter Joints


Miter joints provide one main advantage over other joints: A miter joint hides end grain and brings face grain neatly together. Everything else about miter joints is a hassle. They're fussy, time-consuming and easy to screw up. But there are ways to minimize those hassles.

The 60-Second Squeeze
When you're dealing with small or hard-to-clamp parts, the best clamping tools might be your hands. Simply apply glue to the parts; then rub them together to distribute and tack-set the glue. Hold the parts together on a flat surface for 30 to 60 seconds (although it may seem like 5 minutes). Watch the joint as you release pressure; if anything moves, squeeze and hold for a few more seconds. Let the assembly sit undisturbed for a half-hour before you handle it again.

Make Micro Adjustments with a Disc Sander
No tool can tweak a miter's fit as easily as a disc sander can. You can shorten the workpiece a hair with a quick touch of the disc. You can also adjust the angle by a fraction of a degree. Instead of fussing with the miter gauge, make tiny adjustments by sticking a paper shim between the gauge and the workpiece. Knock-Off Blocks for Long Miters
Long miters are a nightmare to clamp, but adding temporary triangular blocks makes it a snap. The key is to use paper from a grocery bag. Dab some wood glue on both sides of the paper, stick the blocks wherever you need them and let the glue set overnight. When you're done clamping, remove each block with a hammer blow. The paper creates a weak spot in the glue bond, so the blocks break away without damage to the wood. Use hot water to soften any paper or glue left on the wood, then scrape it away and sand as usual. Customize a Drafting Square
Drafting squares are inexpensive, accurate and great for tool or jig setup. Because they're plastic, you can easily customize them to suit the job. We filed notches in this square to keep the saw teeth from interfering with setup. Drafting squares are available in various sizes for $4 to $10 at art and office supply stores. Guides for Perfect Edging
Mitered guides clamped in place let you perfect the length and angle of mitered edging. Use the edging stock itself to guide the fit of each piece. Clamp the guides precisely in place and work your way around the tabletop, gluing each perfected piece in place as you go. After you glue and clamp a section of banding, remove the adjoining guides immediately so you don't accidentally glue them in place.

The Touch Test
When you're building a box or frame, the opposite sides must be precisely the same length. Otherwise, even the most perfect miters won't form a tight joint. To compare lengths, hold the parts together on a flat surface and feel the ends. Your finger can detect differences your eyes c...

Click here to read the rest of the article from American Woodworker