American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tenoning Jigs New Castle DE

Tenoning jigs make the complicated world of mortise-and-tenon joinery a lot simpler. I've used a homemade wooden jig for years. I stand a rail upright on the tablesaw and clamp it to a tall box that slides on my fence. Most shop-made jigs have two drawbacks, though.

Woodcraft - New Castle, DE
(302) 323-0400
Shoppes of New Castle
New Castle, DE

Data Provided by:
The Home Depot
(302)762-3501
3600 Miller Road
Wilmington, DE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(302)369-7080
1000 Suburban Drive
Newark, DE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(302)791-0200
601 Naamans Rd
Claymont, DE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(302)376-5063
350 Auto Park Drive
Middletown, DE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(302)395-1260
138 Sunset Blvd
New Castle, DE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(302)369-6713
1301 New Churchmans Rd
Newark, DE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(302)838-6818
2000 Peoples Plaza
Newark, DE
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Good Hope Hardwoods
(610) 274-8842
1627 New London Road Route 896
Landenberg, PA

Data Provided by:
The Home Depot
(610)459-4278
200 Hatton Drive
Glen Mills, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Tenoning Jigs

Tenoning Jigs



Tenoning jigs make the complicated world of mortise-and-tenon joinery a lot simpler. I've used a homemade wooden jig for years. I stand a rail upright on the tablesaw and clamp it to a tall box that slides on my fence. Most shop-made jigs have two drawbacks, though. First, they must be modified for different types of joints. Second, your fist is the only way to make a fine adjustment to the tablesaw fence. I kept telling myself to look into something better, but the only commercially made jig available a few years ago, the venerable Delta 34-172, didn't tilt and was hard to adjust.

A new generation of redesigned jigs has changed everything (see Chart, click here ). They cost as little as $60, are fully adjustable and are extremely accurate. They fit both left- and right-tilt saws. After trying seven different models, I'm ready to honorably retire my beat-up wooden jig and move on.

All tenoning jigs are remarkably similar, with comparable features and adjustments. Even the least expensive model will give you excellent results.

Most Tenoning Jigs Are Alike


All seven tenoning jigs I tried are surprisingly similar. Remove the handles, paint all the jigs the same color and you would have a hard time telling them apart. Taking a closer look, though, I did find some subtle but important differences. Let's examine their common features first.

Work support. This 5-in.-wide by 6-in.-tall cast-iron plate holds the workpiece. It tilts from 0 to 17 degrees (see Photo 1, below). You can cut steeper angles by tilting the saw blade. On a left-tilt saw, I turn the jig around and run it in the right-hand miter slot when I tilt the blade for steeper angles. This may not work on all saws, however.

Clamp arm. This adjusts forward or backward a total of 2 in. to center the clamp on the workpiece.

Backstop. The backstop tilts backward from 0 to 45 degrees (see Photo 1, below).

Sliding table. The table moves 2-3/8 in. to adjust the distance between the blade and work support.

Coarse adjustment. Loosening a knob allows you to slide the table. Many times, though, you must strike the table with your hand to get it going. That gets old real fast. Lubrication doesn't help much.

Fine adjustment. Turning a knob allows you to fine-tune the sliding table's position. One rotation of the knob moves the table a bit less than 1/16 in. The fine adjustment works so well that I usually skip using the coarse adjustment.

4 User-Friendly Features
Some jigs have additional features that make them easier to set up, adjust and use (see Chart, click here ).

Adjustable guide bar. Some guide bars can be adjusted to fit tightly in your saw's miter slot. This must-have feature increases accuracy by preventing the jig from wiggling as you cut a tenon. The adjustment consists of a pair of set screws in the guide bar, similar to those on premium miter gauges.

Above-jig guide-bar alignment. You must align a new...

Click here to read the rest of the article from American Woodworker

Local Events

Philadelphia Flower Show 2018
Dates: 3/4/2018 – 3/11/2018
Location:
Pennsylvania Convention Center Philadelphia
View Details