American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

The Shadow Knows Keene NH

. Like many lasers, the shadow shows you exactly where the blade is going to cut. But there's a catch with lasers: most of them only show you where one side of the blade will cut. The shadow shows the entire kerf, so it doesn't matter whether your waste piece is on the left or right side of the blade.

Keene - B
(603) 338-5000
480 West St
Keene, NH
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:10-19
Store Features
Mon:9.5-21
Tue:9.5-21
Wed:9.5-21
Thu:9.5-21
Fri:9.5-21
Sat:9-21
Sun:10-19

W W Building Supply
(802) 365-4333
7 Loop Rd
Newfane, VT
 
Rockler Woodworking and Hardware #34
(603) 898-5941
373 S. Broadway
Salem, NH

Data Provided by:
Northland Forest Products, Inc.
(603) 642-3665
16 Church StreetPO Box 369
Kingston, NH

Data Provided by:
Goosebay Sawmill & Lumber
(603) 798-5135
83 Dover Road Route 4
Chichester, NH

Data Provided by:
Jacks True Value Hardware
(603) 352-1517
37 Park Ave.
Keene, NH
 
Best Septic
(802) 463-9444
153 Birchview Ext
Westminster, VT
Services Offered
Waste services, porta potty, jetting, portable toilet rentals, septic solutions, locating septic tanks, septic tank repair, septic tank cleaning, septic tank filters, septic tank services, snaking, camera service, septic trouble shooting, hand wash station rentals, septic design, septic installation, septic maintenance
Hours
24/7 Emergency Service

Woodcraft - Portsmouth, NH
(603) 433-6116
25 Fox Run Road
Newington, NH

Data Provided by:
The Home Depot
(603)542-4471
425 Washington St
Claremont, NH
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

Marquis True Value Hardware
(603) 246-3552
Washington St
West Stewartstown, NH
 
Data Provided by:

The Shadow Knows

The Shadow Knows

 

    

Miter saws equipped with lasers to indicate the line of cut have become commonplace, but DeWalt has a new twist: instead of a laser, DeWalt has developed a super-bright LED light to cast a distinct shadow of the blade on your workpiece. Like many lasers, the shadow shows you exactly where the blade is going to cut. But there's a catch with lasers: most of them only show you where one side of the blade will cut. The shadow shows the entire kerf, so it doesn't matter whether your waste piece is on the left or right side of the blade. And unlike some lasers, this light doesn't have to be aimed–the blade's shadow is always right on the money. DeWalt calls this feature the XPS Worklight. It's available as an accessory for the DW713, DW715, DW716 and DW718 miter saws. Mounting is a cinch; it only takes a few minutes. The light has a separate on/off switch, so the blade doesn't have to be running while you position your workpiece. The one downside–and this is really a minor point–is that the blade must be placed an inch or so above the workpiece for the shadow to pop into sharp focus. DeWalt says that the light bulb should last up to 5 years. That's great, because even if you don't use the shadow technique, the light really illuminates the cut zone, making it much easier to see a fine pencil mark on your work.

Source
DeWalt, www.dewalt.com, 800-433-9258, Miter Saw LED Worklight System, #DWS7085, $60.


Click here to read the rest of the article from American Woodworker