American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

The Shadow Knows Knightdale NC

. Like many lasers, the shadow shows you exactly where the blade is going to cut. But there's a catch with lasers: most of them only show you where one side of the blade will cut. The shadow shows the entire kerf, so it doesn't matter whether your waste piece is on the left or right side of the blade.

The Home Depot
(919)217-3093
1020 Shopps At Midway
Knightdale, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)878-8771
4901 Capital Blvd
Raleigh, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)844-7418
9517 Strickland Rd
Raleigh, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)562-2202
11915 Retail Drive
Wake Forest, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)387-6554
1000 Vision Dr
Apex, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Klingspor’s Woodworking Shop of Raleigh
(919) 876-0707
3141 Capital Blvd.Capital Square
Raleigh, NC

Data Provided by:
The Home Depot
(919)661-1393
2540 Timber Dr
Garner, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Raleigh/Durham, NC
(919) 781-1911
4317 Pleasant Valley Road
Raleigh, NC

Data Provided by:
The Home Depot
(919)851-5554
2031 Walnut Street
Cary, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Robbins Custom Sawing and Lumber for Natural Edge Slabs
(919) 779-0719
2200 Bull Run Drive
Apex, NC

Data Provided by:
Data Provided by:

The Shadow Knows

The Shadow Knows

 

    

Miter saws equipped with lasers to indicate the line of cut have become commonplace, but DeWalt has a new twist: instead of a laser, DeWalt has developed a super-bright LED light to cast a distinct shadow of the blade on your workpiece. Like many lasers, the shadow shows you exactly where the blade is going to cut. But there's a catch with lasers: most of them only show you where one side of the blade will cut. The shadow shows the entire kerf, so it doesn't matter whether your waste piece is on the left or right side of the blade. And unlike some lasers, this light doesn't have to be aimed–the blade's shadow is always right on the money. DeWalt calls this feature the XPS Worklight. It's available as an accessory for the DW713, DW715, DW716 and DW718 miter saws. Mounting is a cinch; it only takes a few minutes. The light has a separate on/off switch, so the blade doesn't have to be running while you position your workpiece. The one downside–and this is really a minor point–is that the blade must be placed an inch or so above the workpiece for the shadow to pop into sharp focus. DeWalt says that the light bulb should last up to 5 years. That's great, because even if you don't use the shadow technique, the light really illuminates the cut zone, making it much easier to see a fine pencil mark on your work.

Source
DeWalt, www.dewalt.com, 800-433-9258, Miter Saw LED Worklight System, #DWS7085, $60.


Click here to read the rest of the article from American Woodworker