American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

The Ultimate Shop-Built Crosscut Sled Fernandina Beach FL

Rube Goldberg-style contraptions to handle various specialty cuts. But I always felt a little queasy with these devices because they put expensive stock (not to mention my fingers) .

Hanna's Woodworks
(912) 576-1243
PO Box 6442
St. Marys, GA

Data Provided by:
The Home Depot
(904)766-2818
12111 Lem Turner Rd
Jacksonville, FL
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(904) 277-5000
474283 East Sr 200
Fernandina Beach, FL
Hours
M-SA 6 am - 9 pm
SU 8 am - 8 pm

Turner Ace Hdw Fernandina
(904) 261-5270
2990 S 8th St
Fernandina Bch, FL
 
Fernandina Bch-Auth Hometwn
(904) 261-5511
1118A South 14Th Street
Fernandina, FL
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:11-16
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:11-16

The Home Depot
(904)225-2940
463785 State Road 200
Yulee, FL
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Kmart 7613 / Cross Merch
(904) 261-2004
1525 Sadler Rd
Fernandina Be, FL
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

LOWE'S OF FERNANDINA BEACH, FL
904 277-5000
3965 EAST S.R. 200 FERNANDINA BEACH, FL, 32034
Fernandina Beach, FL
 
Fernandina Lumber & Supply Co.
(904) 261-3641
117 South 3rd Street
Fernandina Beach, FL
 
St Marys- Auth Hometown
(912) 882-5858
28 Hawthorn Ln
Saint Marys, GA
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9.5-19
Tue:9.5-19
Wed:9.5-19
Thu:9.5-19
Fri:9.5-19
Sat:9-18
Sun:12-17
Store Features
Mon:9.5-19
Tue:9.5-19
Wed:9.5-19
Thu:9.5-19
Fri:9.5-19
Sat:9-18
Sun:12-17

Data Provided by:

The Ultimate Shop-Built Crosscut Sled

The Ultimate Shop-Built Crosscut Sled

It's safe, it slides like a dream and a replaceable throat plate makes it last forever!

by Travis Larson

A good tablesaw sled makes perfect crosscuts easy, accurate and very safe. In addition, a well-designed sled can be used for bevel cuts, dadoes and with a few shop-made jigs,

you can make tenons or repeated miter cuts at any angle.

I used to handle crosscuts with my sliding miter saw (with inevitable tear out). For wider stock, I employed the miter gauge on my tablesaw and sometimes fit it with all sorts of

Rube Goldberg-style contraptions to handle various specialty cuts. But I always felt a little queasy with these devices because they put expensive stock (not to mention my fingers) 

in serious jeapordy. This sled is a much better way to crosscut.

Materials Needed

For this sled you’ll need Baltic birch plywood (one 5x5 sheet), plastic laminate (one 4x8 sheet), plastic runner and guard material, and fasteners—all of which will cost under $100. An equivalent-sized factory-built model sells for about $350 but isn’t designed to handle dadoes or bevel cuts without wrecking the table and fences. Without any mistakes, you should have enough material left over for a miniature sled for lighter, smaller crosscut work.

Tailor the Sled to Suit Your Work

The sled shown in this story handles material up to 24-in. wide, such as cabinet sides and most furniture parts. I haven’t seen many larger sleds, but some people prefer smaller ones. Size your sled wide enough to handle the work you usually do. Some woodworkers use larger sleds for wide work and lighter, smaller, more portable ones for narrow cuts. 

Two Sleds from One Sheet of Plywood

Six hours of shop time will produce this sled. We used a sheet of Baltic birch plywood, and had enough to make a sled for small tasks and the larger model shown here. You can use any 1⁄2-in.- or 3⁄4-in.-thick, cabinet-grade plywood—as long as it’s flat. 

The runners are made of ultra-high molecular weight plastic (1⁄2-in. x 4-ft. x 4-in. sheets run about $20; see Sources, below). Slop-free sizing of the runners is crucial for an accurate sled. They should be the same length as the sled table, just under 3⁄8-in. thick (so they won’t bottom out in the miter slot) and should slide in the slots easily with no side-to-side movement. 

Centering the blade in the table allows for the necessary 2-in. overhang for the stop (Photo 13) on the left side of the saw table and access to the adjusting screw for the fence. Check your saw to confirm that the dimensions of this sled (built to fit a Delta Unisaw) will allow enough overhang. If not, either make the table wider or offset everything so the sled has at least 2-in. overhang over the left side of the saw.

Front Stiffener and Fence

Click here to read the rest of the article from American Woodworker