American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tips and Techniques for Fantastic Oak Finishes Camp Hill PA

Making samples gives you the opportunity to tweak a recipe until you get the look you want. Be sure to make the samples out of scrap from the project you’re finishing to get the most accurate preview of how the finish will look. Sand and finish the samples to the same level as your project and apply a topcoat.

The Home Depot
(717)795-9602
6000 Carlisle Pike
Mechanicsburg, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(717)558-8105
4200 Derry Street
Swatara, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Middletown Lumber
(717) 944-4005
Brown & Clinton Streets PO Box 304
Middletown, PA

Data Provided by:
A.p. Wagner
(716) 856-5005
431 Railroad Ave., Ste A
Camp Hill, PA
 
Ritters True Value Hardware Lemoyne
(717) 731-1070
1200 Market Street
Lemoyne, PA
 
Woodcraft - Harrisburg, PA
(717) 939-6770
777 Eisenhower Blvd.
Harrisburg, PA

Data Provided by:
The Home Depot
(717)651-9699
5101 Jonestown Rd
Harrisburg, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(717)249-1771
1013 S Hanover Street
Carlisle, PA
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Capital City Mall
(717) 760-8000
3595 Capital City Mall
Camp Hill, PA
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9.5-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9.5-21
Sun:11-18

Hepfers Homecenter
(717) 761-7722
313 S 10th St, Highland Park Plaza
Lemoyne, PA
 
Data Provided by:

Tips and Techniques for Fantastic Oak Finishes

Tips and Techniques for Fantastic Oak Finishes

by Dave Munkittrick

 Like a movie star, oak possesses natural good looks. Oak’s distinctive grain pattern (see photo below) is what people are responding to when they say, “I love the look of oak.” Unlike a movie star, however, oak is easy to work with—even during finishing. The best finishes for oak celebrate its grain. In this aricle, I’ll highlight some key finishing tips and techniques used to create the multilayered finishes that bring out the best in oak. Check out the recipes that make use of these techniques in “4 Proven Oak Finishes” .

Earlywood and Latewood Stain Differently

Finishing oak is like finishing two different woods at once.  The large, visible pores in the earlywood soak up stain much more aggressively than the relatively smooth latewood does. 


Avoid Disasters; Make Samples First

Always, always, always make samples before you begin to apply finish. Most finishing disasters can be avoided with this basic step. Making samples gives you the opportunity to tweak a recipe until you get the look you want. Be sure to make the samples out of scrap from the project you’re finishing to get the most accurate preview of how the finish will look. Sand and finish the samples to the same level as your project and apply a topcoat.

Finally, accurately measure and record every step, including dye concentrations, mixture ratios, when to scuff-sand, number of topcoats, etc. There’s nothing worse than hitting on the perfect look only to realize you don’t know how you got there.

Key to a Good Finish: Proper Sanding

I sand oak to 220 grit. Although lots of people stop at 180 grit, I find going one more step really polishes the dense latewood and enhances its contrast with the coarse earlywood. 

Scuff-Sand Carefully

Scuff-sand with 280- or 320-grit paper between coats of shellac and varnish. A light touch is all that’s needed. Care must be taken not to sand through one layer of finish into the next. 

I typically scuff-sand after each coat of shellac. The sanding removes dust nibs and leaves a scratch pattern for the next coat to grip.

Tip: Scuff-sand the dye coat on quartersawn oak to make the ray fleck really pop. Because the rays are so dense, the dye tends to sit on the surface where a light sanding can easily remove it. This makes the rays lighter than the surrounding wood. 

Create a Ground Color with Dye

Many great oak finishes begin with a “ground color” dye, typically a yellow or reddish brown. The ground color establishes the finish’s predominate undertone. Apply the dye liberally to bare wood with a brush or spray bottle. Blot up any excess with a clean rag. Even when thinned to manufacturers’ recommendations, dyes produce very strong colors.

Click here to read the rest of the article from American Woodworker