American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tips for Mastering Featherboards Ankeny IA

This wraparound featherboard produces chatter-free moldings, because it provides continuous pressure ahead of and behind the cutter. Cut a 2-in. arc in the end of the blank before you cut the feathers.

The Home Depot
(515)963-1890
2335 SE Delaware Ave
Ankeny, IA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(515)221-2233
3700 University Ave
West Des Moines, IA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Fastenal- Ankeny
515-964-9413
201 SE Shurfine Suite 5 Ankeny, IA, 50021
Ankeny, IA
 
Park Fair Ace Hardware
(515) 243-6000
100 E Euclid Ste 11, Park Fair Mall
Des Moines, IA
 
BRADLEY TOOLS & FASTENERS, INC.
(515) 331-0878
6250 NW Beaver Dr Ste A-4 Johnston, IA, 50131
Johnston, IA
 
The Home Depot
(515)251-5819
10850 Plum Drive
Urbandale, IA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(515)287-7269
4900 SE 14th St
Des Moines, IA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Johnston Ace Hardware
(515) 276-2854
5800 Merle Hay Rd, HyVee & Greenbriar Restaurant
Johnston, IA
 
Fastenal- Des Moines
515-263-0053
3120 Delaware Ave Des Moines, IA, 50313
Des Moines, IA
 
Merle Hay Mall
(515) 278-7399
4000 Merle Hay Rd
Des Moines, IA
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18

Tips for Mastering Featherboards

Tips for Mastering Featherboards

The featherboard  gets its name from the rows of flexible “fingers” that act like a bird's feather and give way in one direction only. They help ensure safety and accuracy, because they keep consistent pressure on stock where it's needed most, close to the cut. They're indispensable for eliminating bumps on a molded edge or uneven bottoms in rabbets and dadoes. Shop-made featherboards are often superior to commercial ones, because they can be custom fit to your machines and they cost next to nothing. All the featherboards in this article were made from the type of scrap lumber and plywood that can be found in any shop.

Featherboards Made Easy
The safest way to make featherboards is on the bandsaw using a simple sled with a miter slot runner. Cut a 30-degree angle on one end of the featherboard blank first. Mark a parallel line about 2-1/2 in. from the angled end. Set the blank on the sled and make the first cut from the end to the line. Then, slide the featherboard over to the next mark to make the second cut and continue across the board's width. A feather length of about 2-1/2 in. with cuts made every 1/8 in. provides the right balance between flexibility (for firm pressure without being too stiff) and strength (so the feathers won't snap off) for most hardwoods or multi-ply birch. Increase the feather spacing to 3/16-in. when you are using softer woods, such as pine or basswood, or regular hardwood plywood. You can always fine-tune the length and spacing to suit your own needs.



Perfect Pressure Every Time
Positioning a featherboard can be a pain. Too close to the fence or table and the squeeze is so tight you can barely feed the stock. Too loose and you've lost effectiveness. Try taking about 1/8 in. off the first feather. Set that end against the stock you plan to machine and clamp the featherboard parallel to the table's fence. The pressure should automatically be just right.



Tall Support for Tall Stock
A tall featherboard can apply pressure against the entire height of the fence. It's especially useful for holding tall, narrow stock—for instance, a door panel—against a fence. Just glue some scraps to create a block that is as tall as your fence is. Then, cut the feathers on your bandsaw sled.



Bit-Bridging Featherboard
This wraparound featherboard produces chatter-free moldings, because it provides continuous pressure ahead of and behind the cutter. Cut a 2-in. arc in the end of the blank before you cut the feathers.
 


Guaranteed Square EdgesJointing an absolutely square edge on a wide board can be tricky for someone new to the jointer. The least little tip away from the fence and you'll have to start over. This paddle-style featherboard can bridge your jointer's guard while keeping your stock pushed firmly against the fence. The paddle featherboard is easy to make  and is jus...

Click here to read the rest of the article from American Woodworker