American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Tips for Mastering Featherboards Jackson NJ

This wraparound featherboard produces chatter-free moldings, because it provides continuous pressure ahead of and behind the cutter. Cut a 2-in. arc in the end of the blank before you cut the feathers.

Bamboo & Rattan Works, Inc.
(732) 370-0220
470 Oberlin Avenue South
Lakewood, NJ

Data Provided by:
Log Power, Inc.
(609) 259-9709
646B Route 524PO Box 597
Allentown, NJ

Data Provided by:
Howell Plz S/C
(732) 886-3330
4010 Route 9 S
Howell, NJ
Store Hours
Hardware Stores
Store Type
Hardware Stores
Hours
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:9-18
Store Features
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:9-18

Lakehurst Hardware
(732) 657-7180
10 Union Ave.
Lakehurst, NJ
 
Raceway Mall
(732) 303-7000
3710 Route 9 Ste 1100
Freehold, NJ
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21.5
Tue:10-21.5
Wed:10-21.5
Thu:10-21.5
Fri:10-21.5
Sat:9-21.5
Sun:10.5-19
Store Features
Mon:10-21.5
Tue:10-21.5
Wed:10-21.5
Thu:10-21.5
Fri:10-21.5
Sat:9-21.5
Sun:10.5-19

The Home Depot
(609)426-2441
739 Route 33 West
E Windsor, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(609)585-0411
750 Highway Rt 130
Robbinsville, NJ
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(732) 987-7050
4975 Us Highway 9
Howell, NJ
Hours
M-SA 6 am - 10 pm
SU 8 am - 7 pm

Brite Lumber & Home Center
(609) 758-0400
45 Evergreen Rd
New Egypt, NJ
 
Lowe's
(732) 408-2600
1053 Highway 70
Manchester, NJ
Hours
M-SA 6 am - 9 pm
SU 8 am - 7 pm

Data Provided by:

Tips for Mastering Featherboards

Tips for Mastering Featherboards

The featherboard  gets its name from the rows of flexible “fingers” that act like a bird's feather and give way in one direction only. They help ensure safety and accuracy, because they keep consistent pressure on stock where it's needed most, close to the cut. They're indispensable for eliminating bumps on a molded edge or uneven bottoms in rabbets and dadoes. Shop-made featherboards are often superior to commercial ones, because they can be custom fit to your machines and they cost next to nothing. All the featherboards in this article were made from the type of scrap lumber and plywood that can be found in any shop.

Featherboards Made Easy
The safest way to make featherboards is on the bandsaw using a simple sled with a miter slot runner. Cut a 30-degree angle on one end of the featherboard blank first. Mark a parallel line about 2-1/2 in. from the angled end. Set the blank on the sled and make the first cut from the end to the line. Then, slide the featherboard over to the next mark to make the second cut and continue across the board's width. A feather length of about 2-1/2 in. with cuts made every 1/8 in. provides the right balance between flexibility (for firm pressure without being too stiff) and strength (so the feathers won't snap off) for most hardwoods or multi-ply birch. Increase the feather spacing to 3/16-in. when you are using softer woods, such as pine or basswood, or regular hardwood plywood. You can always fine-tune the length and spacing to suit your own needs.



Perfect Pressure Every Time
Positioning a featherboard can be a pain. Too close to the fence or table and the squeeze is so tight you can barely feed the stock. Too loose and you've lost effectiveness. Try taking about 1/8 in. off the first feather. Set that end against the stock you plan to machine and clamp the featherboard parallel to the table's fence. The pressure should automatically be just right.



Tall Support for Tall Stock
A tall featherboard can apply pressure against the entire height of the fence. It's especially useful for holding tall, narrow stock—for instance, a door panel—against a fence. Just glue some scraps to create a block that is as tall as your fence is. Then, cut the feathers on your bandsaw sled.



Bit-Bridging Featherboard
This wraparound featherboard produces chatter-free moldings, because it provides continuous pressure ahead of and behind the cutter. Cut a 2-in. arc in the end of the blank before you cut the feathers.
 


Guaranteed Square EdgesJointing an absolutely square edge on a wide board can be tricky for someone new to the jointer. The least little tip away from the fence and you'll have to start over. This paddle-style featherboard can bridge your jointer's guard while keeping your stock pushed firmly against the fence. The paddle featherboard is easy to make  and is jus...

Click here to read the rest of the article from American Woodworker

Local Events

Philadelphia Flower Show 2018
Dates: 3/4/2018 – 3/11/2018
Location:
Pennsylvania Convention Center Philadelphia
View Details