American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Trim Router Claremore OK

Looking for Trim Router in Claremore? We have compiled a list of businesses and services around Claremore that should help you with your search. We hope this page helps you find Trim Router in Claremore.

The Home Depot
(918)376-9975
9450 N 129th East Ave
Owasso, OK
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Westlake Ace Hardware
(918) 343-3117
810 N Lynn Riggs Blvd
Claremore, OK
 
Pixley Lumber Co
(918) 341-4223
715 W Will Rogers
Claremore, OK
 
Cribbets True Value
(918) 371-3306
1008 Main St
Collinsville, OK
 
Lowe's
(918) 274-0881
12001 E. 96Th Street North
Owasso, OK
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Fastenal- Claremore
918-342-4548
1614 North Lynn Riggs Blvd Claremore, OK, 74017
Claremore, OK
 
Claremore - Auth Hometown
(918) 343-2500
1648 North Lynn Riggs Blvd
Claremore, OK
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:8-20
Store Features
Mon:8-21
Tue:8-21
Wed:8-21
Thu:8-21
Fri:8-21
Sat:8-21
Sun:8-20

Lowe's
(918) 923-1030
1746 South Lynn Riggs Boulevard
Claremore, OK
Hours
M-SA 7 am - 9 pm
SU 8 am - 8 pm

LOWE'S OF OWASSO, OK
918 274-0881
12001 E. 96TH STREET NORTH OWASSO, OK, 74055
Owasso, OK
 
Pryor Lumber
(918) 825-2260
1031 West Highway 20
Pryor, OK
 

7 Trim Router Tips - Techniques - American Woodworker

7 Trim Router Tips

Laminate trim routers are amazing little machines. Their light weight and compact size make them exceptionally easy to use. Although they are designed primarily for trimming plastic laminate (p-lam), they also work great for light-duty wood routing. Trim router motors range from 3.8 to 7.5 amps and run at speeds as high as 30,000 rpm. Add a base and the trim router weighs between 3 and4-1/2 lbs. All models use only a 1/4-in. collet. You can buy a variety of bases and accessories (see Sources, page 4). Prices range from $80 for just the router with a standard base to $250 for a kit with several accessories. Understanding what each of these accessories is capable of doing is thesecret behind getting the most from your trim router. These accessoriesmake the trim router very precise.

 1. Protect the Plastic Laminate Apply a lubricant, such as wax, soap or Trim Ease (a commercial productavailable from p-lam and trim bit distributors), to the plasticlaminate's face when you use self-piloting bits. The lubricant protectsthe p-lam from burning or marring. Self-piloting bits are available inflush-trim or bevel-trim profiles. The flush trim (shown here) is used when you want to leave a flat, square corner. Its single cutting flute makes it fast-cutting. A solid carbide self-piloting trim bit costs $8to $10, which is about half of what a ball-bearing-guided trimming bitcosts.
  
 2. Ball Bearings Reduce Marring Ball-bearing-guided bits greatly reduce the risk of marring and can be used without a lubricant. The bearings do wear out, so you should replace them as soon as they show signs that they're not spinning freely. It's also important to keep them clean of built-up glue. Ball-bearing-guided trim bits are available in either a flush-trim or bevel-trim profile. The bevel profile (shown here) is used when you want to ease the edge to make it friendlier to the touch and reduce its chance of chipping when bumped. Ball-bearing-guided trim bits cost $12to $24 each.

 

 3. Mar-Proof Routing Use a ball-bearing guide attachment when you want to totally eliminate the chance of marring the finished surface or when you want to leave an overhang on the part that you are trimming. A nonpiloted trim bit is used with this guide. The bit is a combination flush and bevel cut. You can trim straight or curved surfaces with this setup.
 4. Get a Super-Straight Cut Use a straight guide when trimming against the substrate material. The straight guide bridges the small voids or gaps common in particleboard and plywood. The result is a straighter edge on the p-lam. This is important when another p-lam piece will be laminated to this edge. Straight edge guides do not work on curves or close in inside corners. A regular straight bit works fine with the straight guide.
 5. Move Close into Corners Use the tilt base when you rout inside corners o...

Click here to read the rest of the article from American Woodworker