American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Tune Up an Old Chisel Apex NC

These steps are equally useful for a new tool, fresh from the box. Please notice that I put equal emphasis on the chisel’s bevel and back. Both must be in perfect condition, for every sharp edge has two sides. Let’s begin with the back.

The Home Depot
(919)387-6554
1000 Vision Dr
Apex, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)851-5554
2031 Walnut Street
Cary, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Raleigh/Durham, NC
(919) 781-1911
4317 Pleasant Valley Road
Raleigh, NC

Data Provided by:
The Home Depot
(919)844-7418
9517 Strickland Rd
Raleigh, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Klingspor’s Woodworking Shop of Raleigh
(919) 876-0707
3141 Capital Blvd.Capital Square
Raleigh, NC

Data Provided by:
Robbins Custom Sawing and Lumber for Natural Edge Slabs
(919) 779-0719
2200 Bull Run Drive
Apex, NC

Data Provided by:
The Home Depot
(919)552-2881
901 E Broad Street
Fuquay Varina, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)661-1393
2540 Timber Dr
Garner, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)419-0208
3701 MT Moriah Road
Durham, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(919)217-3093
1020 Shopps At Midway
Knightdale, NC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Tune Up an Old Chisel

Tune Up an Old Chisel

Turn a Beater into a Razor-Sharp Tool

by Tom Caspar

One of my favorite tools is a legendary Stanley No. 50 chisel. Made in the 1920s, it had seen hard times. Restoring it was a labor of love, and well worth the effort. Its steel holds a long-lasting, super-sharp edge. No doubt you’ve got some beat-up chisels in your toolbox that could be revived, too.

I’ll take you through the complete process of restoring a chisel that’s in tough shape. These steps are equally useful for a new tool, fresh from the box. Please notice that I put equal emphasis on the chisel’s bevel and back. Both must be in perfect condition, for every sharp edge has two sides. Let’s begin with the back.

Evaluate the Back

Inspect the back by sanding with fine paper (Photo 1). Put 220-grit pressure-sensitive-adhesive (PSA) sandpaper on a flat surface, such as a granite surface plate, 1/4-in.-thick piece of glass, cast-iron tablesaw wing or jointer bed. Sand the back a few times using diagonal strokes. Sanding reveals low spots. With an old tool, you’ll probably find rust pits, large hollows or a dip at the leading end. 

Flatten the Back

My chisel’s back looked so bad that I began flattening with 60-grit paper (Photo 2). If the inspection sanding indicates few low spots, begin with a finer grit. The point is to avoid making unnecessarily deep scratches. Machinists call this process lapping. For the coarse work, I use premium-grade sanding belts stretched tightly on a shop-made jig. They can be reused many times, unlike PSA paper. Lapping a back in poor condition may require many strokes, which is hard on your hands, so I often wear rubber-coated gardener’s gloves and take frequent breaks. 

Photo 2: Flatten the back on sandpaper using heavy pressure and diagonal strokes. I prefer to work on a 6-in. x 48-in. sanding belt. It’s easy to reuse and lasts a long time. The belt is stretched taut on a shop-made jig (see “The Lapping Jig, below”).

The Lapping Jig

Opposed wedges tighten a sanding belt placed over this jig. Strike the wedges with a hammer to stretch the paper taut. This jig works for a belt of any size, though I prefer 6-in. x 48-in. belts for their huge surface area. Make the jig from three layers of 3/4-in. MDF glued together. To round the ends, make two 45-degree crosscuts first, and then sand in between them. 

Continue sanding until you reach the bottom of the low spots. How far up the back must you go? Two to three inches are minimum, but I usually lap the whole back. (A totally flat back enables me to use guide blocks when I pare mortises, tenons and dovetails.) If 1/4 in. or less of the back’s leading end is lo...

Click here to read the rest of the article from American Woodworker