American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Turning a Green Wood Bowl Winsted CT

Making a functional object directly from raw material in its natural state is incredibly satisfying. Just ask any potter. For woodworkers, green woodturning captures that feeling. You literally start with a log and end up with a beautiful bowl. If you’ve never turned green wood before, you’re in for a treat.

The Home Depot
(860)496-8620
1580 Litchfield Tpke
New Hartford, CT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(860)286-0300
55 Granby Street
Bloomfield, CT
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-7:00pm

Berkshire Products, Inc.
(413) 229-7919
884 Ashley Falls Rd PO Box 591
Sheffield, MA

Data Provided by:
Lowe's
(860) 618-4273
420 Winsted Road
Torrington, CT
Hours
M-SA 6 am - 10 pm
SU 7 am - 8 pm

C A Lindell True Value Hdw & Lumber
(860) 824-5443
59 Church St
Canaan, CT
 
Moore's Sawmill
(860) 242-3003
171 Mountain Ave
Bloomfield, CT

Data Provided by:
The Home Depot
(860)582-5329
1149 Farmington Ave
Bristol, CT
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Park Place Hardware
(860) 379-4274
11 Park Pl
Winsted, CT
 
Goshen Hardware Inc
(860) 491-3087
59 Torrington Rd
Goshen, CT
 
True Value Home Hdw.&gnd.center
(860) 651-5646
16 Railroad St
Simsbury, CT
 
Data Provided by:

Turning a Green Wood Bowl

Turning a Green Wood Bowl

By Alan Lacer


Making a functional object directly from raw material in its natural state is incredibly satisfying. Just ask any potter. For woodworkers, green woodturning captures that feeling. You literally start with a log and end up with a beautiful bowl.  If you’ve never turned green wood before, you’re in for a treat. Green wood is easier to turn than kiln-dried wood. It cuts cleaner and produces very little dust. To top it off, the wood itself often costs nothing. 

TOOLS AND SUPPLIES: 

• 1/2” bowl gouge 

(from a 5/8” rod)

• 1-1/4 to 1 -1/2-in. 

heavy scraper  

(usually 3/8” thick)

• Jacobs style chuck 

• A 5/8” to 1” drill bit

• Double ended calipers

• Vernier style caliper

• Sanding discs and soft pads (5” and 

2” dia.)

• Flexible shaft tool or flexible shaft for a drill

• 1/8” rubber router mat material

• CA glue

MATERIAL

The process works best if the wood is wet and freshly cut. Storm-downed trees, areas being cleared for development and tree service dumping sites (often called “bone yards”) are all good sources of green wood.  For ease of handling and cutting, choose logs or limbs that are smaller in diameter than your lathe’s swing.  

Almost any species is worth trying, but here are some of my favorites: maple, walnut, butternut, ash, birch, locust, white oak, cherry, beech, Osage orange, and pear. My rule for green bowls is to try whatever is locally available—you may be pleasantly surprised by the abundance of material in your own backyard.   

SAFETY FIRST!

Wet logs weigh a lot! You don’t want one flying off the lathe. Use a faceplate that’s made from one piece of steel and is at least 3/8” thick at the screw hole flange. For bowls less than 10 inches in diameter, I use a 6-hole, 3-in.-diameter faceplate. The type of screw is also critical: Use #12 sheet metal screws. Avoid dry wall, deck and wood screws. Be sure the faceplate sits flat on the log’s surface—if it doesn’t, use a small hand plane across the grain to create the desired fit. Last but not least, be sure to wear a full-face shield—goggles are not sufficient for bowl turning. 

FINISHES

Is your bowl functional (made for food) or decorative?  If it’s decorative, choose any finish that gives the look and feel you prefer. My favorite finishes for functional bowls are mineral oil, walnut oil and pure tung oil. Mineral oil looks great on light colored wood, as it adds no color of its own. However, it never dries so it needs to be reapplied regularly, especially after washing. Walnut oil adds a little color and will dry in time. It’s available at health food stores.  I also like pure tung oil. It adds a deeper color that looks great on dark woods and...

Click here to read the rest of the article from American Woodworker