American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Two-Drawer Coffee Table Bridgeville PA

This table requires only 25 bd. ft. of 4/4 stock and 9 lineal ft. of rough-cut 2-in.-square stock. If you don’t have a jointer and planer, buy turning squares and rip them down to make the legs (see Sources, page 59). The following article has more tips.

The Home Depot
(412)220-2241
1025 Washington Pike
Bridgeville, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(412)494-2844
440 Home Dr
Pittsburgh, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(412)824-9406
3550 William Penn Hwy
Pittsburgh, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(412)367-7346
999 Ross Park Drive
Pittsburgh, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(724)229-7849
255 Murtland Ave
Washington, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(412)835-4271
4000 Oxford Drive
Bethel Park, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(412)650-9460
9971 Mountain View Dr
West Mifflin, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(412)363-9150
400 N Highland Ave
Pittsburgh, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(412)816-1231
102 Aldi Drive
North Versailles, PA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Rockler Woodworking and Hardware #31
(412) 364-7751
7402 McKnight Road
Pittsburgh, PA

Data Provided by:
Data Provided by:

Two-Drawer Coffee Table

Two-Drawer Coffee Table

Pass-through drawers offer two-sided convience

by Tim Johnson

A coffee table isn’t just for coffee. It displays interesting reading and serves the Saturday night pizza. It hosts Scrabble games, labors under kids’ crafts and gives you a place to rest your feet. It’s a real workhorse that has to be well built and versatile. Our table is rock-solid, featuring mortise-and-tenon joints, splines, and dovetailed drawers. It’s also easy to build, because simple, shop-made jigs ensure perfect-fitting joints. Its two drawers act like four, because they open from both sides. A standard dovetail jig is all you need to make them. Rare-earth magnets work like magic as two-way drawer stops (see Sources, below).

This table requires only 25 bd. ft. of 4/4 stock and 9 lineal ft. of rough-cut 2-in.-square stock. If you don’t have a jointer and planer, buy turning squares and rip them down to make the legs (see Sources, page 59). Buy 3/4-in.-thick boards for everything else but the drawer sides. Get 1/2-in.-thick boards for them and a 2 ft. by 4 ft. piece of 1/4-in. plywood for the drawer bottoms. We built our table from cherry, and used birch for internal parts and drawer sides. Our cost, including one-half sheet of 3/4-in. birch plywood for the jigs and clamping cauls, came to about $250.

The only must-have power tools for this project are a tablesaw and a plunge router equipped with an edge guide. You’ll also need a drill, a coping saw, a sharp 1/4-in. chisel, glue and the usual assortment of clamps, including four 4-ft. pipe clamps.

Start at the Top

I always make the top of a table right off the bat, for two reasons. First, it’s the most important part, visually, so it deserves the best-looking boards. Make the aprons, rails and drawer fronts from the leftovers.  Second, you can start finishing the top early, so the finish will have plenty of time to cure. This is especially important if you plan to build up layers of finish for long-lasting protection. Be sure to apply equal layers to both sides of the top, to keep it stable. 

I like to use hide glue when I work with cherry, because of its dark color. Its long open time also makes it easy to fine-tune the joints between the top boards (Photo 1). Wait 24 hours before you remove the clamps. Hide glue takes a long time to dry.

Cut the top (A) to size, smooth it and soften all the edges. I use a router with a 1/8-in. round-over bit for this, but sandpaper and a block will work. If you have children, you may also want to round the four corners for safety.

Photo 1:  USE YOUR BEST BOARDS FOR THE TOP. Choose ’em and use ’em right away, so you don’t get caught short later. Cauls above and below keep the boards aligned and flat during glue-up. Use a non-marring mallet to make minor adjustments.Size Up the Legs

The four legs (B) are mortised, dadoed and tapered (Fig...

Click here to read the rest of the article from American Woodworker