American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Versatile Router-Bit Storage Cabot AR

Versatile router-bit storage is not that hard to make. The following article has 8 tips to offer to help you build your own tool stand. So read on to get more detailed instruction below.

The Home Depot
(501)941-4350
555 Going Road
Cabot, AR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Kmart 3933 / Cross Merch
(501) 843-2206
W Main Street
Cabot, AR
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21
Store Features
Mon:8-22
Tue:8-22
Wed:8-22
Thu:8-22
Fri:8-22
Sat:8-22
Sun:8-21

Whit Davis Lumber Plus
(501) 982-2156
723 School Dr
Jacksonville, AR
 
LOWE'S OF JACKSONVILLE, AR
501 241-1500
2301 T.P. WHITE DRIVE JACKSONVILLE, AR, 72076
Jacksonville, AR
 
LOWE'S OF N. LITTLE ROCK, AR
501 955-2219
4330 EAST MCCAIN BOULEVARD NORTH LITTLE ROCK, AR, 72117
North Little Rock, AR
 
The Home Depot
(501)945-3500
4325 E McCain Blvd
North Little Rock, AR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Whit Davis Lumber Plus
(501) 843-7009
340 Arena Road
Cabot, AR
 
Fastenal- Jacksonville
501-982-2442
617 J.P. Wright Loop Jacksonville, AR, 72076
Jacksonville, AR
 
Lowe's
(501) 241-1500
2301 T. P. White Drive
Jacksonville, AR
Hours
M-SA 7 am - 10 pm
SU 8 am - 8 pm

Lowe's
(501) 955-2219
4330 East Mccain Boulevard
North Little Rock, AR
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Versatile Router-Bit Storage

Versatile Router-Bit Storage

When it comes to router-bit storage, I could write a book. I’ve tried everything, but I think my latest design is a keeper. 

I prefer to keep my bits protected in a drawer. At first, I just drilled some holes in a block of MDF and set that into the drawer. But it proved difficult to thread my hand through the forest of sharp carbide when reaching for a bit. Several bandages later, I had a better idea. I cut 3/4-in. MDF into square blocks small enough to fit in a row inside the drawer but big enough to hold my panel-raiser bit. I left about 1/16 in. of clearance around each block so I can easily lift them in and out. It’s best to keep the blocks square, so you don’t have to turn one this way or that to fit it in its space. I drilled holes for the 1/2-in. shanks using a 33/64-in. twist bit and for 1/4-in. shanks using a 17/64-in. bit. The slightly oversize holes allow the bits to slip easily in and out. 

To avoid reaching into the sharp bits, I cut some 5/16-in. dowel stock to make handles for lifting the blocks. The knobs at the top are made from 3/4-in. wooden balls I picked up at a craft and hobby store. Now it’s easy to select just the bit I want and take it right to the router table.

Click here to read the rest of the article from American Woodworker