American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Versatile Router-Bit Storage Chagrin Falls OH

Versatile router-bit storage is not that hard to make. The following article has 8 tips to offer to help you build your own tool stand. So read on to get more detailed instruction below.

The Home Depot
(330)562-6000
18800 N Market Pl Drive
Aurora, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(330)908-1300
8211 Macedonia Commons
Macedonia, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(440)684-1343
6199 Wilson Mills Rd
Highland Heights, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(330)422-0401
9585 State Route 14
Streetsboro, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(216)692-1861
877 E 200th St
Euclid, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Woodcraft - Cleveland, OH
(440) 232-7979
22745 Rockside Road
Bedford, OH

Data Provided by:
The Home Depot
(216)581-6611
21000 Libby Rd
Maple Heights, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(216)297-1303
3460 Mayfield Rd
Cleveland Heights, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(440)285-7400
287 Meadowlands Drive
Chardon, OH
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(440)895-4420
21669 Center Ridge Rd
Rocky River, OH
Hours
Mon-Thur: 7:00am-9:00pm
Fri-Sat: 7:00am-10:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Versatile Router-Bit Storage

Versatile Router-Bit Storage

When it comes to router-bit storage, I could write a book. I’ve tried everything, but I think my latest design is a keeper. 

I prefer to keep my bits protected in a drawer. At first, I just drilled some holes in a block of MDF and set that into the drawer. But it proved difficult to thread my hand through the forest of sharp carbide when reaching for a bit. Several bandages later, I had a better idea. I cut 3/4-in. MDF into square blocks small enough to fit in a row inside the drawer but big enough to hold my panel-raiser bit. I left about 1/16 in. of clearance around each block so I can easily lift them in and out. It’s best to keep the blocks square, so you don’t have to turn one this way or that to fit it in its space. I drilled holes for the 1/2-in. shanks using a 33/64-in. twist bit and for 1/4-in. shanks using a 17/64-in. bit. The slightly oversize holes allow the bits to slip easily in and out. 

To avoid reaching into the sharp bits, I cut some 5/16-in. dowel stock to make handles for lifting the blocks. The knobs at the top are made from 3/4-in. wooden balls I picked up at a craft and hobby store. Now it’s easy to select just the bit I want and take it right to the router table.

Click here to read the rest of the article from American Woodworker