American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 
» » »

Versatile Router-Bit Storage Galax VA

Versatile router-bit storage is not that hard to make. The following article has 8 tips to offer to help you build your own tool stand. So read on to get more detailed instruction below.

Galax - Auth Hometown
(276) 238-8600
972 E Stuart Dr
Galax, VA
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-20
Thu:9-20
Fri:9-20
Sat:9-19
Sun:12-18
Store Features
Mon:9-19
Tue:9-19
Wed:9-20
Thu:9-20
Fri:9-20
Sat:9-19
Sun:12-18

Lowe's
(276) 238-3000
8417 Carrollton/Pike Road
Galax, VA
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Blevins Do it Best Building
(336) 372-4000
652 North Main Street
Sparta, NC
 
The Home Depot
(540)943-9000
31 Windigrove Road
Waynesboro, VA
Hours
Mon-Sat: 7:00am-9:00pm
Sun: 8:00am-7:00pm

The Home Depot
(703)591-6808
3201 Old Lee Highway
Fairfax, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Blevins Do it Best Building
(276) 236-8171
302 South Main Street
Galax, VA
 
LOWE'S OF GALAX, VA.
276 238-3000
8417 CARROLLTON/PIKE ROAD GALAX, VA, 24333
Galax, VA
 
Blevins Do it Best Building
(336) 363-2216
7258 Hwy 21 South
Glade Valley, NC
 
The Home Depot
(757)833-8101
325 Chatham Road
Newport News, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(703)823-1900
400 S Pickett St
Alexandria, VA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Versatile Router-Bit Storage

Versatile Router-Bit Storage

When it comes to router-bit storage, I could write a book. I’ve tried everything, but I think my latest design is a keeper. 

I prefer to keep my bits protected in a drawer. At first, I just drilled some holes in a block of MDF and set that into the drawer. But it proved difficult to thread my hand through the forest of sharp carbide when reaching for a bit. Several bandages later, I had a better idea. I cut 3/4-in. MDF into square blocks small enough to fit in a row inside the drawer but big enough to hold my panel-raiser bit. I left about 1/16 in. of clearance around each block so I can easily lift them in and out. It’s best to keep the blocks square, so you don’t have to turn one this way or that to fit it in its space. I drilled holes for the 1/2-in. shanks using a 33/64-in. twist bit and for 1/4-in. shanks using a 17/64-in. bit. The slightly oversize holes allow the bits to slip easily in and out. 

To avoid reaching into the sharp bits, I cut some 5/16-in. dowel stock to make handles for lifting the blocks. The knobs at the top are made from 3/4-in. wooden balls I picked up at a craft and hobby store. Now it’s easy to select just the bit I want and take it right to the router table.

Click here to read the rest of the article from American Woodworker