American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Versatile Router-Bit Storage Indianola IA

Versatile router-bit storage is not that hard to make. The following article has 8 tips to offer to help you build your own tool stand. So read on to get more detailed instruction below.

The Home Depot
(515)287-7269
4900 SE 14th St
Des Moines, IA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Circle B
(515) 961-5381
1700 North Jefferson
Indianola, IA
 
Acme Tools-Des Moines
515-244-4189
629 SW 9th Street DES MOINES, IA, 50309
Des Moines, IA
 
Amana Society Forestry
(319) 622-7554
1300 220th Trail PO Box 189
Amana, IA

Data Provided by:
Scandinavian Woodshop /Sawmill
(515) 548-3449
2835 Baxter Avenue
Somers, IA

Data Provided by:
Mccoy True Value Hdw
(515) 961-4755
216 N Howard St
Indianola, IA
 
South Ridge Mall Ste 2002
(515) 287-4720
1111 Se Army Post Rd
Des Moines, IA
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:11-18

The Home Depot
(515)221-2233
3700 University Ave
West Des Moines, IA
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

The Home Depot
(319)294-0480
4501 1st Avenue SE
Cedar Rapids, IA
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

The Home Depot
(712)255-5310
415 Cunningham Drive
Sioux City, IA
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

Data Provided by:

Versatile Router-Bit Storage

Versatile Router-Bit Storage

When it comes to router-bit storage, I could write a book. I’ve tried everything, but I think my latest design is a keeper. 

I prefer to keep my bits protected in a drawer. At first, I just drilled some holes in a block of MDF and set that into the drawer. But it proved difficult to thread my hand through the forest of sharp carbide when reaching for a bit. Several bandages later, I had a better idea. I cut 3/4-in. MDF into square blocks small enough to fit in a row inside the drawer but big enough to hold my panel-raiser bit. I left about 1/16 in. of clearance around each block so I can easily lift them in and out. It’s best to keep the blocks square, so you don’t have to turn one this way or that to fit it in its space. I drilled holes for the 1/2-in. shanks using a 33/64-in. twist bit and for 1/4-in. shanks using a 17/64-in. bit. The slightly oversize holes allow the bits to slip easily in and out. 

To avoid reaching into the sharp bits, I cut some 5/16-in. dowel stock to make handles for lifting the blocks. The knobs at the top are made from 3/4-in. wooden balls I picked up at a craft and hobby store. Now it’s easy to select just the bit I want and take it right to the router table.

Click here to read the rest of the article from American Woodworker