American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Versatile Router-Bit Storage West Fargo ND

Versatile router-bit storage is not that hard to make. The following article has 8 tips to offer to help you build your own tool stand. So read on to get more detailed instruction below.

The Home Depot
(701)282-2078
4700 17th Avenue SW
Fargo, ND
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 12:00pm-8:00pm

Kmart 4057 / Cross Merch
(701) 232-8943
2301 S University Dr
Fargo, ND
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Fastenal- Fargo
701-277-0823
3215 Main Ave Suite A Fargo, ND, 58102
Fargo, ND
 
West Acres Regional S/C
(701) 281-5800
3902 13Th Ave South Ste 600
Fargo, ND
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Dakota Fastening
(701) 298-3691
3401 1/2 Interstate Blvd Fargo, ND, 58103
Fargo, ND
 
Ostrom's Hardware
(701) 282-3046
1100 13th Ave E Ste 2, 9th St and 13th Ave E
West Fargo, ND
 
Lowe's
(701) 433-2160
5001 13Th Avenue Sw
Fargo, ND
Hours
M-SA 7 am - 9 pm
SU noon-8 pm

Nodak Stores
(701) 293-1155
3515 W Main Ave
Fargo, ND
 
Simonson Lumber & Hdw True Value
(701) 232-3281
2400 Main Ave
Fargo, ND
 
Lamperts
(701) 492-0292
4115 32nd Ave Sw
Fargo, ND
 

Versatile Router-Bit Storage

Versatile Router-Bit Storage

When it comes to router-bit storage, I could write a book. I’ve tried everything, but I think my latest design is a keeper. 

I prefer to keep my bits protected in a drawer. At first, I just drilled some holes in a block of MDF and set that into the drawer. But it proved difficult to thread my hand through the forest of sharp carbide when reaching for a bit. Several bandages later, I had a better idea. I cut 3/4-in. MDF into square blocks small enough to fit in a row inside the drawer but big enough to hold my panel-raiser bit. I left about 1/16 in. of clearance around each block so I can easily lift them in and out. It’s best to keep the blocks square, so you don’t have to turn one this way or that to fit it in its space. I drilled holes for the 1/2-in. shanks using a 33/64-in. twist bit and for 1/4-in. shanks using a 17/64-in. bit. The slightly oversize holes allow the bits to slip easily in and out. 

To avoid reaching into the sharp bits, I cut some 5/16-in. dowel stock to make handles for lifting the blocks. The knobs at the top are made from 3/4-in. wooden balls I picked up at a craft and hobby store. Now it’s easy to select just the bit I want and take it right to the router table.

Click here to read the rest of the article from American Woodworker