American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Vine Trellis Jonesboro AR

Frame the front and back faces of the trellis (Photo 6). Align the beveled ends of the slats with the edges of the legs and drill pilot holes. Then drill out the holes in the slats so the screws slip through. Apply glue and assemble.

The Home Depot
(870)268-0619
711 W Parker
Jonesboro, AR
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

ABC Supply Co.,Inc/Jonesboro
870-931-3550
2501 Commerce Dr Jonesboro, AR, 72401
Jonesboro, AR
 
Fastenal- Jonesboro
870-931-5424
1909 Amanda Ln. Jonesboro, AR, 72401
Jonesboro, AR
 
Kmart 7356 / Cross Merch
(870) 972-9020
2010 S Caraway Rd
Jonesboro, AR
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :0-0 and for Sat:0-0
Sun:0-0
Store Features
Monday To Friday Working Hours is :0-0 and for Sat:0-0
Sun:0-0

LOWE'S OF JONESBORO, ARK.
870 930-9000
2111 FAIR PARK BLVD. JONESBORO, AR, 72401
Jonesboro, AR
 
Hilltop Ace Hardware
(870) 932-1311
4827 East Johnson Ave
Jonesboro, AR
 
Lowe's
(870) 930-9000
2111 Fair Park Blvd
Jonesboro, AR
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

Indian Mall
(870) 974-7800
1901 S Caraway Rd Ste 1
Jonesboro, AR
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-18

Bartons Do it center
(870) 932-6675
3023 Browns Lane
Jonesboro, AR
 
SFS Jonesboro
870-935-2232
3105 Prosperity Drive Jonesboro, AR, 72404
Jonesboro, AR
 

Vine Trellis

Vine Trellis

Before you set aside your push sticks and dust mask for the season, make  something to enjoy all summer. This project takes only about a day to build, once you've got all the materials. It's designed for outdoor use—made from rot-resistant woods and assembled with weatherproof glue and rust-resistant fasteners. Protected with a finish or not, it will enhance your garden or deck for years to come. 

Make any climbing plant happy with this 6-ft. tall, free-standing trellis. We used dadoes, glue and screws to fasten the slats because trellises take a beating each year when you tear off the old vines. We built our trellis from cypress, one of the longest-lasting outdoor woods. Ours was recycled from old water tanks and cost about $175. White oak, at $60, would also be a good choice.

Marking the legs for the dadoes can be confusing, but if you follow our marking procedures (Photos 1 through 4), you can't mess up. Even with our easy-to-make jigs, routing 68 dadoes is noisy, dusty and tedious (Fig. B and Photo 5). But once they're done, the dadoes make assembly foolproof. There's only one angle to remember: Everything slopes 6 degrees.

You'll need an angled template, made with the miter gauge on your tablesaw, to make the dadoing jigs. You'll also need a router with a straight bit to cut the dadoes, and a drill with a slotted tip for all the screws. We used a jointer and planer to mill our parts to thickness, but they could also be ripped to size on a tablesaw. The slats are thin, so be sure to use a push stick.

How To Build It

1) Mill the legs (A) to thickness and cut them to length. 

2) Mark the leg dadoes (Photos 1 through 4 ). The sides of the trellis are tapered, so the dadoes are angled. 

3) Cut an 84-degree angled template, about 10-in. long and at least 4-in. wide. Use it to set the fence angle on the dadoing jigs (Fig. B).
4) Dado the legs (Photo 5). One jig will slope the right direction for the 3/16-in. deep dadoes on one side of each leg. The mirror-image jig will be correct for the other side.

5) Mill slat material to thickness and rip it into lengths, slightly oversize in width. Then plane (or rip) the slats to fit the leg dadoes.

6) Cut the bottom and top slats (B through E) for all four sides to length, with a 6-degree bevel on both ends. You can cut the slats to length in pairs because opposite sides of the trellis are the same.

7) Frame the front and back faces of the trellis (Photo 6). Align the beveled ends of the slats with the edges of the legs and drill pilot holes. Then drill out the holes in the slats so the screws slip through. Apply glue and assemble.

8) Cut the internal slats (F) to fit, and fasten them, following the procedures in Steps 6 and 7.

9) Stand the assembled front and back faces back-to-back in an "A," and assemble the sides, following Steps 7 and 8.

Click here to read the rest of the article from American Woodworker