American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Walnut Coffee Table with Curved Legs Yankton SD

There's something that pleases a woodworker's soul when you make a whole project from just one board. It's really satisfying to study a big plank with all its problems, such as knots, sapwood and runout grain, and figure out how you're going to cut it into smaller pieces (Photo 1). Thick, large boards are a luxury, though.

Yankton - Auth Hometown
(605) 665-7861
2901 Broadway Ave
Yankton, SD
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17
Store Features
Mon:9-19
Tue:9-19
Wed:9-19
Thu:9-19
Fri:9-19
Sat:9-18
Sun:12-17

Kmart 4813 / Cross Merch
(605) 665-8025
2210 Broadway Ave
Yankton, SD
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Kruse True Value
(402) 254-3840
207 N Summit Ave
Hartington, NE
 
The Home Depot
(605)361-7439
2523 S Louise Ave
Sioux Falls, SD
Hours
Mon-Sat: 6:00am-9:00pm
Sun: 8:00am-8:00pm

A&c Variety&true Value Hdwe
(605) 698-3451
419 Veterans Ave
Sisseton, SD
 
Ace Hardware
(605) 260-2813
2404 Broadway Ave, Across the street from Bonanza
Yankton, SD
 
Fullerton Lumber Co 938
(605) 665-9651
2409 Broadway Ave
Yankton, SD
 
Carhart Lumber Co.
(402) 254-3928
119 E Main
Hartington, NE
 
Homestead Building Supplies
(605) 763-5046
201 E. Main St
Beresford, SD
 
Britton Lumber & Home Center
(605) 448-5282
767 Vander Horck
Britton, SD
 

Walnut Coffee Table with Curved Legs

Walnut Coffee Table with Curved Legs

Download the pdf file.

WalnutCoffeeTable1.pdf

I've been hoarding some huge, air-dried walnut boards for over twenty years, waiting for the right projects to come around. This small coffee table was the perfect opportunity to finally cut one open and get my hands on the rich figure inside.

There's something that pleases a woodworker's soul when you make a whole project from just one board. It's really satisfying to study a big plank with all its problems, such as knots, sapwood and runout grain, and figure out how you're going to cut it into smaller pieces (Photo 1). Thick, large boards are a luxury, though. You can certainly make this table from separate boards instead, using standard 1 and 2- in. thick wood. See Figure A and Cutting List.

MAKE THE TOP

1) Resaw boards for the top (A) (Photo 2). Cut them 3/4 in. thick, then joint and plane the boards ½ in. thick (Photo 3). Glue the top together and cut it to exact size.

2) Rout two dovetailed grooves across the bottom of the top (Fig. B and Photo 4). First, install a 1/2-in. wide dovetail bit and a 1/2-in. dia. template guide in your router. Next, build a jig composed of four pieces to guide the router. Use 1/2-in. thick material. Assemble the jig using two 5/8-in. thick spacers to fix the distance between the rails. The router's bit and template guide setup makes a groove that's exactly the same width as the distance between the jig's rails.

DOVETAILED CLEATS

3) Make cleats (E) from a stiff hardwood that resists splitting. Maple is ideal. Make one or two extra pieces to test your router-table settings.

4) Shape the cleat's dovetailed key on the router table (Photo 5). Set the height of the router bit so that the key is a paper-thickness shallower than the grooves in the tabletop. (You don't want the cleat to drag against the bottom of these grooves when you insert it.) Adjust the router table's fence until the cleat fits right (Photo 6). Remove the cleats from the table.

5) Finish the top by drawing a shallow curve along both of its long sides (Fig. D). Bend a 3-ft. long stick to form the curve. Cut the curve using a jigsaw or bandsaw. Round over the bottom edge of the top using a router (Fig. B). Use a smaller roundover bit on the top's upper edge. Use a file to soften the top's four corners.

SHAPE THE LEGS

6) Make a pattern for the legs (D) from 1/4-in. thick wood (Fig. G). Mill leg blanks and trace around the pattern on two adjoining sides (Photo 7).

7) Mill mortises before bandsawing the legs. Begin by routing grooves for the tenon's haunch (Fig. E, Photo 8). Deepen the mortises with a mortising machine (Photo 9).

8) Cut the legs on the Bandsaw (Photo 10). Saw one side first, then turn the leg 90 degrees. Lay the pattern on the leg and mark the portion of the curve that was removed by sawing. Saw the other side.

Click here to read the rest of the article from American Woodworker