American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Wedged Mortise & Tenon Fort Morgan CO

Experiment with the notch's angle. The wider the taper, the stronger the joint. My taper is 3 degrees, but you can increase it up to 8 degrees. 4. Test the bend. My flexible strips are only 1/8 in. thick opposite the strain-relief hole, so they bend easily.

Bloedorn Lumber Building Mtrls
(970) 867-5646
130 State Street
Fort Morgan, CO
 
Ft Morgan - Auth Hometown
(970) 867-5200
1997 E Piatte Ave
Fort Morgan, CO
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12.5-17.5
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12.5-17.5

Murdoch's Ranch & Home Supply
(970) 542-1515
1207 W. Platte Avenue
Fort Morgan, CO
 
Country Do it Best Hardware
(970) 483-7312
218 Main St.
Wiggins, CO
 
The Home Depot
(303)799-9071
9401 E Arapahoe Rd
Greenwood Village, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Fastenal- Ft. Morgan
970-867-4475
19873 US Highway 34 Ft. Morgan, CO, 80701
Ft. Morgan, CO
 
Mr. D'S Ace Home Center
(970) 867-3303
1000 East Platte Avenue
Fort Morgan, CO
 
Farm & Home Hardware
(970) 842-2879
122 Custer St
Brush, CO
 
The Home Depot
(303)205-5141
7200 W Colfax Ave
Lakewood, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

The Home Depot
(303)706-1500
8477 S Yosemite Ave
Lone Tree, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Wedged Mortise & Tenon

Wedged Mortise & Tenon

The joint will never loosen!

by Tom Caspar

Tap, tap, tap. The wedges go home, the glue squeezes out and a big smile lights up your face. “This joint isn’t coming apart for a hundred years,” you say. “It’s as solid as a rock!”

Making a wedged mortise-and-tenon joint is richly rewarding. Once you understand how it works (see photo, below), you can’t help but admire the joint’s elegant simplicity. It also sends a message. A wedged joint says to one and all, “This was made by a skilled woodworker.” 

How the Joint Works

Here’s a cutaway view of a wedged mortise-and-tenon joint. Driving in the wedges forces the tenon to flare into a fan or dovetail shape. The mortise is tapered to match the angle of each wedge. Like a dovetail, this joint can’t pull apart after the wedges go home.

This tenon has two unusual features: saw kerfs that create flexible strips and holes that disperse the strain that the wedges create. The wedges cause the strips to bend; the holes prevent the bend from splitting the rail.

Where could you use a wedged joint? It’s a candidate for any joint that receives a lot of stress. A table base is a good example (top photo). Pushing or leaning on this table might slowly force a standard joint apart, but wedges keep this joint locked together. 

The wedged mortise-and-tenon joint isn’t difficult to make, but you should have some experience making standard mortise-and-tenon joints before tackling it.

Tools Required

To make this joint, you’ll need a tablesaw, drill press, plunge router, chisel and a bandsaw. If your mortise’s width is 5/8 in. or more, like the mortise I made, you’ll need a 1/2-in.-dia. top-bearing flush-trim bit ($19). If the mortise is more than 3/4 in. deep, you’ll need a bottom-bearing flush-trim bit ($20) (see Source, below). For a mortise less than 5/8 in. wide, you’ll need a straight router bit and a fence or jig for your plunge router.

Rout the Mortise

Before you begin your project, make a prototype joint (see photo, below). 

Designing Your Wedged Joint

Each part of a wedged joint must often be tailored to fit the joint’s size, intended strength and type of wood. Make a prototype following these steps: 

1. Substitute a notch made with a dado set for the mortise (see “How the Joint Works,” page 45). Taper both of the notch’s sides by angling the miter gauge.

2. Make a full-size tenon. Observe how well the flexible strips bend. You may be able to use smaller strain-relief holes or no holes at all.

3. Experiment with the notch’s angle. The wider the taper, the stronger the joint. My taper is 3 degrees, but you can increase it up to 8 degrees. 

4. Test the bend. My flexible strips are only 1/8 in. thick opposite the strain-relief hole, so they bend easily.

Click here to read the rest of the article from American Woodworker