American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Wedged Mortise & Tenon Spartanburg SC

Experiment with the notch's angle. The wider the taper, the stronger the joint. My taper is 3 degrees, but you can increase it up to 8 degrees. 4. Test the bend. My flexible strips are only 1/8 in. thick opposite the strain-relief hole, so they bend easily.

The Home Depot
(864)574-2922
121 Dorman Center Drive
Spartanburg, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Lowe's
(864) 216-4934
120 East Blackstock Road
Spartanburg, SC
Hours
M-SA 6 am - 10 pm
SU 8 am - 8 pm

LOWE'S OF SPARTANBURG, S. C.
864 576-7744
100 PEACHWOOD CENTRE DR SPARTANBURG, SC, 29301
Spartanburg, SC
 
Blue Eagle Equipment
864-583-0700
350 TNS Road Spartanburg, SC, 29303
Spartanburg, SC
 
LOWE'S OF BOILING SPRINGS, SC
864 573-2771
170 RAINBOW LAKE ROAD BOILING SPRINGS, SC, 29316
Boiling Springs, SC
 
The Home Depot
(864)579-0382
2300 E Main Street
Spartanburg, SC
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 8:00am-8:00pm

Westgate Mall
(864) 587-5300
205 W Blackstock Rd Ste C
Spartanburg, SC
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:9-21
Sun:12-18

Fastenal- Spartanburg
864-948-9600
67 Dexter Rd Spartanburg, SC, 29303
Spartanburg, SC
 
Lowe's
(864) 573-2771
170 Rainbow Lake Road
Boiling Springs, SC
Hours
M-SA 7 am - 9 pm
SU 9 am - 7 pm

Ace Hardware
(864) 578-7008
3433 Boiling Springs Road
Spartanburg, SC
 

Wedged Mortise & Tenon

Wedged Mortise & Tenon

The joint will never loosen!

by Tom Caspar

Tap, tap, tap. The wedges go home, the glue squeezes out and a big smile lights up your face. “This joint isn’t coming apart for a hundred years,” you say. “It’s as solid as a rock!”

Making a wedged mortise-and-tenon joint is richly rewarding. Once you understand how it works (see photo, below), you can’t help but admire the joint’s elegant simplicity. It also sends a message. A wedged joint says to one and all, “This was made by a skilled woodworker.” 

How the Joint Works

Here’s a cutaway view of a wedged mortise-and-tenon joint. Driving in the wedges forces the tenon to flare into a fan or dovetail shape. The mortise is tapered to match the angle of each wedge. Like a dovetail, this joint can’t pull apart after the wedges go home.

This tenon has two unusual features: saw kerfs that create flexible strips and holes that disperse the strain that the wedges create. The wedges cause the strips to bend; the holes prevent the bend from splitting the rail.

Where could you use a wedged joint? It’s a candidate for any joint that receives a lot of stress. A table base is a good example (top photo). Pushing or leaning on this table might slowly force a standard joint apart, but wedges keep this joint locked together. 

The wedged mortise-and-tenon joint isn’t difficult to make, but you should have some experience making standard mortise-and-tenon joints before tackling it.

Tools Required

To make this joint, you’ll need a tablesaw, drill press, plunge router, chisel and a bandsaw. If your mortise’s width is 5/8 in. or more, like the mortise I made, you’ll need a 1/2-in.-dia. top-bearing flush-trim bit ($19). If the mortise is more than 3/4 in. deep, you’ll need a bottom-bearing flush-trim bit ($20) (see Source, below). For a mortise less than 5/8 in. wide, you’ll need a straight router bit and a fence or jig for your plunge router.

Rout the Mortise

Before you begin your project, make a prototype joint (see photo, below). 

Designing Your Wedged Joint

Each part of a wedged joint must often be tailored to fit the joint’s size, intended strength and type of wood. Make a prototype following these steps: 

1. Substitute a notch made with a dado set for the mortise (see “How the Joint Works,” page 45). Taper both of the notch’s sides by angling the miter gauge.

2. Make a full-size tenon. Observe how well the flexible strips bend. You may be able to use smaller strain-relief holes or no holes at all.

3. Experiment with the notch’s angle. The wider the taper, the stronger the joint. My taper is 3 degrees, but you can increase it up to 8 degrees. 

4. Test the bend. My flexible strips are only 1/8 in. thick opposite the strain-relief hole, so they bend easily.

Click here to read the rest of the article from American Woodworker