American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Wood Edging on Laminated Tops Gardnerville NV

To trim off a whisker, try this: With the miter saw off, drop the blade down and push the mitered end of the edging up against the teeth with enough pressure to ever so slightly deflect the blade. With a tight hold on the edging, raise the blade back up.

The Home Depot
(775)267-3434
921 Jacks Valley Road
Carson City, NV
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Meek's
(775) 782-6889
1405 Industrial Way
Gardnerville, NV
 
Scottys Hardware
(775) 588-5681
264 Kingsbury Grade
Stateline, NV
 
Best Building Supply
(530) 541-8726
1920 Lake Tahoe Blvd
South Lake Tahoe, CA
 
Nels Tahoe Hardware
(530) 544-4126
1050 Fremont St
South Lake Tahoe, CA
 
SILVER STATE ROOFING MATERIALS
(775) 782-7663
1434 Industrial Way Gardnerville, NV, 89410
Gardnerville, NV
 
Ace Hardware
(775) 782-5211
1406 Industrial Way, INDUSTRIAL WAY off HWY 395
Gardnerville, NV
 
Zephyr Cove - Auth Hometown
(775) 588-8723
183 Hwy 50
Zephyr Cove, NV
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:10-15
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:10-15

Kmart 9153 / Cross Merch
(530) 541-8971
1030 Tata Lane
South Lake Ta, CA
Store Hours
Miscellaneous
Store Type
Miscellaneous
Hours
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21
Store Features
Monday To Friday Working Hours is :8-22 and for Sat:8-22
Sun:8-21

Scottys True Value Hardware
(530) 541-3601
1931 Lake Tahoe Blvd
South Lake Tahoe, CA
 

Wood Edging on Laminated Tops

Wood Edging on Laminated Tops

5 steps to align and finish wood edging on a plastic-laminated surface.

by Bruce Kieffer

Most woodworkers cringe at the thought of applying wood edging to a plastic-laminated top. Unlike wood veneer surfaces, you can’t sand this edging flush without scratching the laminate. Over the years, I’ve discovered a few tricks of the trade that will help you avoid messy glue-ups and misaligned edging. 

Even after you’ve successfully applied the trim, you still face a woodworking conundrum: applying finish to the wood edge but not the laminate. I found a special automotive masking tape that works better than I could imagine. Applying any type of finish is now fast and clean. Just follow these easy steps for a clean-looking, hassle-free top. 

Cutting the Miters

The first hurdle is to cut your edging pieces’ mitered corners to fit exactly—you can’t get away with being a hair short or long. Start with the two long trim pieces. Use a short piece of edging with a mitered end to test-fit the long pieces. Leave the end pieces about 1/16 in. long; they’ll be trimmed to fit later. Finish-sand the top edges of the edging pieces before you glue them on. You don’t want to sand the top of the trim after it’s applied and risk scratching the laminate. After the long runs are glued in place, you can cut and fit the end pieces for airtight miters. 

Photo 1: Use biscuits to avoid alignment nightmares. You’ll never have a wood edge dip below the laminate surface if you cut the slots so the wood edge sets just a smidgen above the laminated top. To do this, cut the slots in the wood edging first. Then use the same setting with a sheet of paper under the fence to cut the slots in the laminated top. Use No. 20 biscuits and set the slots 4 in. to 6 in. apart. 

Photo 2: Glue on one piece of edging at a time. Glue-up disasters often result from attempts to glue everything at once. Start with the long edging pieces. After they’re set, trim the mitered end pieces for an exact fit (see Photo 3). To eliminate squeeze-out on the laminate surface, apply glue only to the inside of the biscuit slots and a bead along the edge below the biscuits. 

Photo 3: The end pieces are cut slightly oversize and then trimmed to create a tight joint. To trim off a whisker, try this: With the miter saw off, drop the blade down and push the mitered end of the edging up against the teeth with enough pressure to ever so slightly deflect the blade. With a tight hold on the edging, raise the blade back up. Turn the saw on and slowly make the cut. This will take the lightest shaving off the end and allow you to work your way to the perfect fit. 

Photo 4: Get a clean crisp finish line using 3M’s Scotch Fine Line Tape (see Source, page 62). This is truly a “magic” masking tape!

Click here to read the rest of the article from American Woodworker