American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Wooden Plate Portales NM

All you'll need is a small face plate, a medium-sized bowl gouge (3⁄8-in. to 1⁄2-in.), a round-nose scraper, some masking tape and alarge, thick chunk of wood for the chuck. A plate blank that's 9- to10-in. wide works best. It can be glued-up or cut from a wide board,just as long as one side is flat and smooth.

Portales Ace Hardware
(575) 356-6711
227 S Main Ave
Portales, NM
 
LOWE'S OF CLOVIS, NM
505 742-4000
3601 NORTH PRINCE STREET CLOVIS, NM, 88101
Clovis, NM
 
Fastenal- Clovis
505-763-9335
1306 State Rd. 209 Clovis, NM, 88101
Clovis, NM
 
Hacienda Home Centers
(575) 769-2651
200 East Brady Avenue
Clovis, NM
 
PGP, Inc.
505-762-6654
1729 W. 21st Clovis, NM, 88101
Clovis, NM
 
Furrow's Home Lumber Inc.
(575) 763-4437
1201 E 1st Street
Clovis, NM
 
Burns Hardware Do it center
(575) 769-2528
1511 N Prince St
Clovis, NM
 
North Plains Mall
(575) 769-4700
2811 N Prince St
Clovis, NM
Store Hours
Sears Stores
Store Type
Sears Stores
Hours
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18
Store Features
Mon:10-21
Tue:10-21
Wed:10-21
Thu:10-21
Fri:10-21
Sat:10-21
Sun:12-18

Lowe's
(575) 742-4000
3601 North Prince Street
Clovis, NM
Hours
M-SA 7 am - 9 pm
SU 9 am - 8 pm

Triangle Ace Hardware
(575) 762-3301
2400 N Prince St, North plains mall
Clovis, NM
 

Wooden Plate

Wooden Plate

Got an offcut from a beautifully figured board? Turn it into aplate! Standard 3⁄4-in. wood and a shop-made chuck are all you need.

The trick is to figure out how to hold such a thin piece of wood on thelathe. It's so thin, there's hardly anything to grab onto. Here's asafe and simple system for turning a plate from thin wood.

All you'll need is a small face plate, a medium-sized bowl gouge(3⁄8-in. to 1⁄2-in.), a round-nose scraper, some masking tape and alarge, thick chunk of wood for the chuck. A plate blank that's 9- to10-in. wide works best. It can be glued-up or cut from a wide board,just as long as one side is flat and smooth. You'll need that flatsurface in order to glue the plate blank onto a mounting block. To makethe blank, cut off a square piece from the wide board and cut it into arough circle with a bandsaw. Draw a 3-in. circle in the center of theblank's smooth side. Then make a 3-in.-dia. mounting block from a pieceof 1-in.-thick wood that's been surfaced on both sides. Screw themounting block onto a small face plate. Now follow the photo sequenceand create your own stunning plate.

PHOTO 1:
Gluethe mounting block onto the plate blank. Use medium- to thick-viscositycyanoacrylate (CA) glue. It dries quickly, so you'll be ready to turnin two to three minutes. Adjust your lathe to run at its lowest speed.Then mount the face plate on the lathe and true up the face and edge ofthe blank with a bowl gouge.


PHOTO 2:
Round the plate's rim with the bowl gouge turned on its side. Thisprevents the gouge from catching and is called a “closed cut.” Move inthe direction of the arrow and swing the handle of the gouge around thecorner. Ride the bevel of the gouge on the plate, keeping the cut verylight.

PHOTO 3:
Flattenthe face of the plate. Work from the outside to the center. Keep thebevel of the gouge rubbing against the plate to make this shearing cut.Because you are working with thin material, use light shearing cuts,especially around the rim. You can place your hand behind the rim toreduce vibration.


PHOTO 4:
Cut a cove to define the rim. Drop the handle of the gouge below thelevel of the tool rest so the gouge won't catch. Keep the bevel ridingon the plate.
Next dish out the center of the plate with shearing cuts. Measure the depth of the plate before you cut too deep.
If you're careful you should be able to make a very smooth surfaceacross the entire face of the plate with the gouge. You can move righton to sanding. But if you've had some trouble and there are tool marksyou can't get out, reach for a scraper.

PHOTO 5:
Scrapethe face of the plate with light cuts for a smooth surface. Move fromthe center out to the edge. Raise the handle of a round-nose scraperabove the level of the tool rest so its cutting edge won&...

Click here to read the rest of the article from American Woodworker