American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

Wooden Television Cabinet Conway AR

This page provides useful content and local businesses that give access to Wooden Television Cabinets in Conway, AR. You will find helpful, informative articles about Wooden Television Cabinets, including "Television Cabinet". You will also find local businesses that provide the products or services that you are looking for. Please scroll down to find the local resources in Conway, AR that will answer all of your questions about Wooden Television Cabinets.

Claflin Custom Cabinets Inc
(501) 470-1541
44 Imperial Lane Conway
, AR
 
Grants Custom Cabinets
(501) 679-5292
199 Linder Road Greenbrier
, AR
 
McCrorys Custom Cabinets
(501) 796-8339
18 Graddy Loop Vilonia
, AR
 
Powell Creative Woods Inc.
(501) 868-6353
23301 Highway 300 Roland
, AR
 
Custom Carpentry & Carpenter Millworks
(501) 758-2279
10585 Maumelle Boulevard North Little Rock
, AR
 
B & B Custom Cabinets
(501) 796-2258
31 Rock Crusher Road Conway
, AR
 
Mcgintys Cabinetry
(501) 679-7235
23 Business Park Drive Greenbrier
, AR
 
Austen Michaels Custom Interiors Blinds & Fine Cabinetry
(501) 851-2134
Maumelle
, AR
 
Custom Millwork
(501) 851-4421
1200 Murphy Drive Maumelle
, AR
 
Pennington Ray Cabinet Shop
(501) 835-3101
65 Wesley Drive Sherwood
, AR
 

Television Cabinet - Projects - American Woodworker

Television Cabinet

Hide the electronics behind ingenious double-hinged doors.

by Dave Munkittrick

I love my new 36-in. TV but my wife hates what the glass and plastic monolith does to the look and feel of our family room. To avoid marital strife we went looking for something to house the behemoth. No luck. Sounds like a job for the family woodworker! I love it when I get a chance to justify my sometimes-controversial investment in the shop. 

A cabinet large enough to accommodate a 36-in. TV could look like an oversized shipping crate. But I used a design with angled corners to ease the big-box look. 

Note: There are a few extra-deep 36-in. TVs that may require you to cut a hole in the back for the TV to poke through. You could make a deeper cabinet but you’d have to buy an additional sheet of plywood. Play it safe; buy your TV first, then adjust the depth if necessary. 

The double-hinged doors fold flat against the sides to open up the cabinet for unobstructed viewing. Plus, they’re a whole lot cheaper and easier to install than pocket doors. The adjustable, no- mortise, partial-wrap hinges (see Sources, below) make these doors a snap to hang. 

Ventilation and Wire Management

Double-hinged doors fold flat against the sides, leaving the screen wide open for optimal viewing. Because the doors are double jointed, they can be operated with as little as 14 in. of side clearance.

A conveniently located drawer with full-extension slides allows easy access to a treasure trove of movies.

Cost and Materials

I chose pine for its rustic feel. Plus, I love the smell of fresh-cut pine in my shop. 

Pine plywood is a special-order item and comes with either knotty or clear veneers (see Sources, page 92). You can expect to pay about $600 in materials for this project.

Ventilation and Wire Management

Big TVs kick out a lot of heat, so adequate ventilation is a must. The cabinet is designed to let the heat escape through a series of vent holes (Fig. A). 

Holes at the bottom of the upper crosspiece and at the back of the TV shelf allow both wires and heat to pass through. All the wires funnel out of an 8-in.-dia. hole in the back (Fig. A). The removable back allows easy access to the snake’s den of wires behind the TV and its components.

You’ll Need a Well-Equipped Shop

To build this project you’ll need a tablesaw, a stacking dado set, bandsaw, biscuit joiner, screw gun, router table, router, pneumatic brad and finish nailer, planer, miter saw and at least six 6-ft. pipe clamps. 

Check your router bit collection for a 1/2-in. Roman ogee, a 1/2-in. cove, a 1/2-in. round over, a flush trim (top or bottom bearing), and a chamfer bit. If you want to make your own bun feet, you’ll also need a 1-in. round-over bit (see Sources, below). 

Build some knee-high sawhorses to support an oversized asse...

Click here to read the rest of the article from American Woodworker