American Woodworker
Contact Us | Help | Report a Bug
Sign in | Join
 

World's Best Routing Guide Fort Morgan CO

The guide works perfectly with your router, because you use your router to make it. Make the base extra wide; then trim it with your router. Now when you use the guide, the routed base indicates the edge of the cut, as long as you rout with the same bit or another bit with the same diameter.

Fastenal- Ft. Morgan
970-867-4475
19873 US Highway 34 Ft. Morgan, CO, 80701
Ft. Morgan, CO
 
Mr. D'S Ace Home Center
(970) 867-3303
1000 East Platte Avenue
Fort Morgan, CO
 
Ft Morgan - Auth Hometown
(970) 867-5200
1997 E Piatte Ave
Fort Morgan, CO
Store Hours
Hometown Dealers
Store Type
Hometown Dealers
Hours
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12.5-17.5
Store Features
Mon:9-18
Tue:9-18
Wed:9-18
Thu:9-18
Fri:9-18
Sat:9-18
Sun:12.5-17.5

Country Do it Best Hardware
(970) 483-7312
218 Main St.
Wiggins, CO
 
The Home Depot
(303)688-8790
333 W Allen Street
Castle Rock, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Murdoch's Ranch & Home Supply
(970) 542-1515
1207 W. Platte Avenue
Fort Morgan, CO
 
Bloedorn Lumber Building Mtrls
(970) 867-5646
130 State Street
Fort Morgan, CO
 
Farm & Home Hardware
(970) 842-2879
122 Custer St
Brush, CO
 
The Home Depot
(303)706-1500
8477 S Yosemite Ave
Lone Tree, CO
Hours
Mon-Sat: 6:00am-10:00pm
Sun: 7:00am-8:00pm

Woodcraft - Denver, CO
(303) 290-0007
6770 S. Peoria St
Centennial, CO

Data Provided by:
Data Provided by:

World's Best Routing Guide

World's Best Routing Guide

This simple guide guarantees success whenever you need to make a straight routing pass. It’s perfect for jointing a long edge or routing dadoes and grooves. You’ll get smooth, chatter-free results, thanks to the guide’s firm support fence. Positioning the guide is foolproof, because it’s dedicated to the bit you plan to use.  

The guide is nothing more than a 1/2-in.-thick fence glued to a 1/4-in.-thick base. The base protrudes by the radius of the router’s base. The fence must have a straight edge—I used the factory edge of my MDF. Routing the base with a straight bit completes the guide (see photos, below). 

To use, simply align the guide’s base with your cutline on the workpiece. Clamp the guide in position and rout, using the same straight bit that you used to complete the guide. For best results, don’t try to remove more than 1/16 in. from the edge or to rout a dado deeper than 1/4 in. at a time.

The guide works perfectly with your router, because you use your router to make it. Make the base extra wide; then trim it with your router. Now when you use the guide, the routed base indicates the edge of the cut, as long as you rout with the same bit or another bit with the same diameter.

A short guide is perfect for routing dadoes and rabbets. Make sure the guide extends beyond the workpiece on both ends.

Difficult operations, such as squaring the ends of a large tabletop, are a breeze. When you rout end grain, clamp a block against the back edge, so you don’t blow it out.

Click here to read the rest of the article from American Woodworker